New to the radio restoration world
Posts: 8
Threads: 3
Joined: Mar 2014
City: Canada
Hey there guys and gals. I recently aquired a philco 1775 and completely new to the whole restoration thing! I've done alittle searching and haven't been able to find much information on this particular model. Here's what I know or atleast was told by the former owner. It's a Canadian made model, has hi-fi and a turn table. It was said to be made 1960.
Curently there is no sound other then pops & crackles from the speakers on both FM & AM. I have yet to try a record so I cannot say how the sound is from there. Within the next few weeks I hope to open it up and start taking a look around the inside(currently garage is too cold from the winter).Once I do this I hope to get some of the over 50 years of grime out.
Any tips or suggestions would greatly be apprechiated as I can't wait to get started in this new hobby!
Posts: 395
Threads: 33
Joined: Jul 2013
City: Horsham, PA
Chuck,
Welcome to the Phorum!
You will need to replace the electrolytic and paper/wax caps. Don't know anything about restoring record players myself, xso I'll leave that to others.
Jon
Posts: 8
Threads: 3
Joined: Mar 2014
City: Canada
Jon,
Thanks for the response. I'll dtake your advise and look those items
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
Welcome Chuck. Can you give us an indication of experience/knowledge in old electronics and an idea of what test equipment you have? It will give us a basis to start you on your journey when the weather improves. Perhaps someone here will have a copy of the schematic for you. You can't go on a journey without a "road map".
Best, Jerry
A friend in need is a pest! Bill Slee ca 1970.
(This post was last modified: 03-29-2014, 01:08 PM by jerryhawthorne.)
Posts: 8
Threads: 3
Joined: Mar 2014
City: Canada
Hi Jerry,
My experience is almost zero with electronics at this point. I do however understand the baiscs in how things work(the threory and science) but have never took on a project like this. As far as tools, I'm limited there as well, but can buy as needed and any advice or sugestions on what to buy & what to avoid would greatly be apprechiated. As far as schematics I do have those and trying to learn how to read them.
Posts: 395
Threads: 33
Joined: Jul 2013
City: Horsham, PA
Chuck,
I recommend you start with a lot of reading. Here are a couple of great sites to get you started.
http://www.antiqueradio.org/welcome.htm
http://www.antiqueradio.org/welcome.htm
Lots of other sites as well. And of course, this site is a tremendous resource with lots of knowledgeable people who are willing to help.
Jon
Posts: 599
Threads: 24
Joined: Jan 2014
City: Edmonton AB CA
Hey Chuck:
Welcome to the Phorum from another Canuck! What part of our great land are you in?
Gregb
Posts: 8
Threads: 3
Joined: Mar 2014
City: Canada
Thanks again jon. I will check those out. Right now I'm watching a schematics reading lesson on you tube http://youtu.be/KbvM5Tkc-UA
Greg- I'm from St Catharines Ontario
Posts: 395
Threads: 33
Joined: Jul 2013
City: Horsham, PA
Glad to help.
I messed up the paste of the second web address. Here's another try.
http://www.philcorepairbench.com
Jon
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
Chuck, at the minimum you will need a soldering iron (40 watt pencil) and a volt and ohm meter. Harbor Freight has one for about $6. Will work and when you hook things up wrong (ie set in ohms and measuring voltages) it will probably die. Not much invested. It will do the job.
If you can, post the schematic or a link to it so we can follow the journey.
Best, Jerry
A friend in need is a pest! Bill Slee ca 1970.
Posts: 5,072
Threads: 269
Joined: Nov 2012
City: Bandon
State, Province, Country: OR
Welcome to the Phorum. Here's a thread that relatively recent on the topic of books useful for learning about radio electronics. It digresses in to other topics by the second set of pages but perhaps it will help.
Posts: 761
Threads: 56
Joined: Jul 2013
City: Kentucky
Welcome to the forum! Once you get that set playing, you'll become addicted and you'll be searching for other radios. One thing to always keep in mind - you are working with potentially lethal voltages. Make sure you follow safety guidelines... make sure you are never grounded (don't stand on a concrete floor, etc), keep one hand in your pocket, etc. You should make a dim bulb tester before you begin your work, etc.
Good luck and keep us informed!
The artist formerly known as Puhpow! 8)
Posts: 8
Threads: 3
Joined: Mar 2014
City: Canada
I guess what I had was not the schematics so i will need those, but I can't seem to find my model listed anywhere.
Posts: 1,947
Threads: 146
Joined: Jan 2013
City: Westland, MI
Hi Chuck! Welcome to the phorum, eh? Hope you aren't going to be kicking yourself like I am for selling all my vinyl at garage sales!! Take care, Gary
"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
Chuck, a schematic for your radio is critical with your level of experience. My level as well. Many here just seem to know what has to be what. If you get no response here, post in the for sale/buy sub forum. Generally some other Canuck will have a listing of radios made in Canada and probably copy and send to you N/C. Justradios in Canada also have schematics for sale and may be able to help. Your radio being "newer" means that Sams Photofact is no doubt the source. They supplied schematics around that time for devices like yours. Prewar schematics were covered well and can be found at Nostalgia Air's web site.
Have fun and be safe. As indicated there are some high voltages in there. Without a schematic it is hard for us to tell just exactly how safe you need to be. All radios have high voltages but some "later" radios without a power transformer known as AC/DC radios have other real safety concerns. The schematic will tell a lot.
Enjoy the adventure and as indicated earlier, when you get this up and running, you will be looking for another! It is a disease.
Jerry
A friend in need is a pest! Bill Slee ca 1970.
(This post was last modified: 03-31-2014, 12:32 PM by jerryhawthorne.)
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
Restoring Philco 37-604C
|
| Hello mike,
My Stand also has some very minor rust too and mine is used inside my heated house .
Sincerely Richardradiorich — 11:02 PM |
|
Philco 10 car radio head key
|
| Hi Keandkafu,
In general, the Key Code usually has nothing to do with the brand of key, but is a code for how the not...MrFixr55 — 10:37 PM |
|
Radiola 18 Amplifier & PS
|
| If the 2.25V winding is not being used, the center tap wire can be insulated by taping off. If the 5V filament winding ...MrFixr55 — 07:33 PM |
|
Hippo 46-420 Schematic doesn't match parts list.
|
|
Here you have the part in the sch with values.
I am not sure what else is needed.morzh — 02:56 PM |
|
Restoring Philco 37-604C
|
| Ron
Here are the two of my jigs side by side. They have been with me about the same time (a couple of month differenc...morzh — 02:05 PM |
|
Kurt P
|
| Terry, gotcha, thanks for the clarification. That’s probably why the speaker seems shorted. Assuming the OT/FC/speaker...Kurt P — 10:59 AM |
|
Radiola 18 Amplifier & PS
|
| I have the 2.25V and 2.5V information confused, and must look more carefully at the schematic and Hammond transformer in...TN Allen — 10:24 AM |
|
Radiola 18 Amplifier & PS
|
| Thank you for the information, it all helps, although understanding some of it takes time. One reason for doing the PS a...TN Allen — 09:42 AM |
|
462ron
|
| Hi Mike, the radio is coming along nicely but wow, you must have some serious moisture in your shop judging by the amoun...462ron — 06:29 AM |
|
Restoring Philco 37-604C
|
| Have rebuilt the can.
The can had 4 caps in it, 2x16uF, 10uF and 8uF.
I used a 15uF as the first cap, 22uF and 10uF ...morzh — 09:38 PM |
|
Who's Online
|
| There are currently no members online. |
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
