Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

bathtube cap
#1

can anyone tell me what a common lug on a bathtub cap is used for, is it a ground lug, if so how is it different from the other bathtub cap with out the common lug
thank you for your help
john
#2

Caps do not have ground lugs, they just have lugs. These can be connected to whatever including ground.

A cap with a common case and two lugs is simply a dual cap with one common. Connect it any way you will.
#3

John, to expand a bit on Morzh's comment, if your referring to the black Philco bakelite caps they generally have a lug on the end the mounting screw goes through. This lug would be chassis ground. Components inside the tub often require one end to ground and this is used for that connection. Should you find a can without a lug on that end (I don't recall seeing any) it just means that the component(s) inside do not need to be connected to ground thus the lug was left off.
Make sense? Chuck's Philco repairbench site will provide a listing of the various tub caps listed by the number etched in their sides. It provides the value(s) of the internals and their connection point.
Chuck's site: http://www.philcorepairbench.com/bblokcap.htm
Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#4

Jerry,

No, bathtubs are these:

http://www.tedss.com/144P107M/?gclid=CO-...7Aodch4AQQ
or
http://www.surplussales.com/capacitors/BathtubCaps.html

Often oil filled.
#5

My bad, I was thinking of Philcos where I have seen them called many things, often derogatory.
Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#6

Those little guys are expensive.

The artist formerly known as Puhpow! 8)
#7

Those are "audio quality" oil-filled caps. Yes, they are expensive.

You mainly see them in audio-phile gear or test equipment.

Some high-end radios also used them. My Scott 800B has them. I tested several and they were all right on, so I left them alone.

I have a box full of them I got from my friend and mentor Bob Timms. Many are appropriate values for my Scott, I am saving them for my Great-Grand Children to have in case one of the ones in my Scott eventually fail.

In fact, I believe that when the atomic apocalypse comes, the only things left will be cockroaches and oil-filled caps.
#8

Quote:In fact, I believe that when the atomic apocalypse comes, the only things left will be cockroaches and oil-filled caps.

...and I will add - the tar from thousands of restuffed Philco bakelite blocks. .Icon_lol ..Somewhere, scattered across the globe.

The artist formerly known as Puhpow! 8)
#9

No....it will mix with asphalt roads.

It will only be found in rural areas....
#10

If you melt the bakelite block tar in a bowl and add sugar it's great on pancakes.
#11

Or you can then introduce yeast, fement it, take it to a nearby still and make "Philco noir" moonshine.
#12

Pardon me, but I thought bathtub caps were used in HV circuits of CRT high voltage supplies in ancient televisions and could cause house fires when failed, but it has been a while...........
#13

Bathtub cap is the one you charge and throw in a bathtub while your MIL is enjoying her bubbles.
#14

..I'd like to do that with the bathtub AA5..Icon_lol

The artist formerly known as Puhpow! 8)




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco Model 80 Transformer resistance
Just forget this number, it is useless anyway. Simply proceed with your project.morzh — 10:08 PM
Philco Model 80 Transformer resistance
My $0.02 is that it is a misprint. I tried to look up the value for the similar 84 and 37-84, and ther is no resistance...MrFixr55 — 09:51 PM
Philco Model 80 Transformer resistance
Thanks for the quick reply! Hmm...well that's good, so what am I seeing that's 1042 ohms on the schematic for the pow...Mike L — 08:46 PM
Philco Model 80 Transformer resistance
The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM
Philco Model 80 Transformer resistance
I have a feeling the primary winding on the power transformer is bad. My resistance reading on the primary side is 9 ohm...Mike L — 07:48 PM
Rusty Tuning Condenser
I would try Naval Jelly and use a soaked pipe cleaner to get it where it needs to go.RossH — 06:56 PM
38-10T chassis Restoration begins
Hello Dconant , they sold mica to use as a insulator between transistors and their heatsinks too. Rob I will remove th...radiorich — 02:52 PM
38-10T chassis Restoration begins
Thanks for the info guys. I always wondered why the use of mica. Now I know.dconant — 01:52 PM
38-10T chassis Restoration begins
Most common plastics have a dielectric constant in the 3-4 range whereas mica is around 6. This means that even if you w...Steve D — 01:46 PM
38-10T chassis Restoration begins
It is acceptable but not desirable. Plastic is not an approved cap dielectric, and even though a reasonably thick piece...morzh — 11:52 AM

[-]
Who's Online
There are currently 3814 online users. [Complete List]
» 1 Member(s) | 3813 Guest(s)
Avatar

>