Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Radiola 18
#1

Could someone please let me know where the antenna hooks up to on a radiola 18 ar936? I finally received the ux280 tube and everything powers up but I don't even hear a chirp. I'm about ready to throw the towel in on this thing
#2

There should be a marked antenna post somewhere on the thing. Also, look at the back of the cabinet, might be marked 'ANT' near a hole on the back to give you a clue.

No matter where you go, there you are.
#3

Radiola 18's don't have antenna posts. They have two wires coming out from the right hand side of the main chassis. These connect directly to the chassis ground and to the input of the 1st RF amp with a resistor across them. If I get a chance, I'll take a pic of one of my chassis' later today and post it for you.
#4

I was remembering a different TRF chassis (a Steinite, I believe). It is much the same, however, with the 18 chassis. The antenna and ground wires come in on the far left side of the chassis, and run up to connect into the volume control. See pics below:

   

   

   
#5

Thank you very much. Those definitely help. The schematic I found had the speaker wired up to there!
#6

Eek... the speaker plugs into the two pin jacks on the power supply chassis.
#7

Here's an accurate schematic:

http://www.nostalgiaair.org/PagesByModel...040317.pdf

Note it shows both the DC (top) version and the AC (bottom) version. You'll see the volume control labeled as such on the DC version, on the AC version it's in the same place but not labeled.

The following document might help you also, it has voltages, component values, and tips on the 18:

http://www.nostalgiaair.org/References/A...la18-2.htm

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#8

Are those jacks hopefully 3.5mm like headphone jacks or a bit bigger?
#9

Those are for pin jacks, like they used on old headphones and speakers. Mouser sells them:

http://www.mouser.com/ProductDetail/Keys...toqrxdU%3d

So does Radiodaze as the SPC-TIP:

http://www.radiodaze.com/product/400.aspx

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#10

Thanks Brenda! She fired right up and gave a great sound! Have to do some work on the volume control though. Also thanks John, I ordered a set!
#11

Goes to show you how long it's been since I have looked at a Radiola 17 or 18. Used to be common as dirt around here.

No matter where you go, there you are.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 40-100
Arran, I restored 2 Canadian battery-crank telephones for a friend a while ago, a Northern Electric (Canadian version of...MrFixr55 — 08:04 AM
Road Trip for a Philco 46-480
Beautiful work, a 79 year old radio brought back to life. The first FM radios for me, a little iffy, had some I just cou...Jimradio — 08:01 AM
Philco 46-480 Electronic Restoration
I was a field engineer for a biomedical company for many years. Many was the time that I was driving home from NYC in t...MrFixr55 — 06:40 AM
Philco 46-480 Electronic Restoration
Don't laugh folks, I have not been above taking a chassis into the bathtub (when Ms. Fixr was out of the house), taping ...MrFixr55 — 06:02 AM
Philco model 40-100
Marion; By "newer style" carbon resistors do you mean the molded type with coloured bands rather then the BE...Arran — 01:00 AM
Philco 46-480 Electronic Restoration
hello jrblasde , your radio sounds great well done !! I bought like 20 years ago a Philco 610b that someone had painte...radiorich — 11:50 PM
Philco model 40-100
Arran, I just can't tell if the volume control has been replaced. The control has a brass shaft with one half flat for ...mhamby — 11:08 PM
Philco model 40-100
You may be able to make the part out of wood. The particular vendor has a habit of disassembling radios and selling the...MrFixr55 — 10:09 PM
Philco 46-480 Electronic Restoration
Used to get to Bentonville when I worked for a Walmart vendor....nice and sleepy back then. PaulPaul Philco322 — 09:49 PM
Philco Model 249 made in England
Did Garrard produce stand-alone turntables? The reason I ask is, when I was a kid my grandfather gave me a KLH Model 20 ...jrblasde — 09:37 PM

[-]
Who's Online
There are currently 579 online users. [Complete List]
» 3 Member(s) | 576 Guest(s)
AvatarAvatarAvatar

>