Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

I got one!
#1

Finally found an AK 'little stove'! A model 53. Actually stumbled on this at an antique mall I usually never find anything of interest in this afternoon. Other than the missing fine tuning knob it appears complete. Tuner is currently stuck, but I don't see any serious damage inside.

   

   

   

No matter where you go, there you are.
#2

nice project, Looks heavy

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#3

Keep the stove but find a radio chassis that is less rusted.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#4

Most AKs you find around here have some rust on the inside. It's that wonderful, humid Ohio air. I doubt finding another complete chassis is going to happen as this one is a bit different from the AK breadboxes I have lying around. For one thing, this unit has a regular electro-dynamic speaker, not the early high-impedance units. It's an eight tube chassis that appears to use push-pull 71's as outputs. Also, I think the 'chassis' is actually part of the cabinet. It appears you can pull out the RF deck and transformer deck separately, but that's it. Actually, it looks like getting the parts out might be a real pill. The original AK instructions even mentions having to cut some wires! Eek!

No matter where you go, there you are.
#5

Not so long ago Terry got one.
#6

Good score! Those are not seen everyday so you did well. I like small funky consoles like those.

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#7

Large knob on left is from an earlier AK set.
#8

Heavy ain't it!!!!
Terry
#9

Yep it IS heavy. I was wondering about the knob. I wonder if the spare knob from my parts 42 might be a better match or just leave it be?

No matter where you go, there you are.
#10

Wow nice tind! But I would not liked to be zapped Leaning on a all metal radio if the electronic was not up to par....Wow wee...
#11

I think the AK-42 knob would work.
#12

A picture with the correct knobs now installed. Makes the radio look a good bit different. Also, got the tuner sort of loose. Two of the gangs turn, but the drive belt for the third is damaged and it appears someone has loosed the nut on the back, causing all the plates to become mis-aligned! Oh well, that can be corrected and maybe a full tuner alignment will help with performance. Oh, the transformer appears good, so major plus there! Icon_thumbup

   

No matter where you go, there you are.
#13

If you need a new belt Adams sells replacement bronze belts for A.K.'s:

http://www.adamsradio.com/

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#14

Thanks! I'll have to see if the broken belt is the long or short one.

No matter where you go, there you are.




Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Philco 42-1008 conversion kit
I read about a kit to convert the variable speed changer in the Philco 42-1008 into a single speed unit.  That would rem...alangard — 09:30 PM
HiFi (Chifi) tube amp build - but my own design.
Tim Well...a chassis is metal. Magnetic or not, it does not matter. A transformer has some hum to it. It is natural....morzh — 08:40 PM
Hickok AC51 tube tester
I thought the 83 tube was bad because it looked white but it tests strong. Blue gassy though. I checked the fuse, it was...martinj — 08:37 PM
Shadow Meter Bulb
Ross I am not sure what current limiting effect the incandescent provides. They are two different parts of the sch...morzh — 08:31 PM
12' Philco
Bob Thanks for that photo. I have been looking for it, and I cannot find anythinmg on the web. I forgot it was here...morzh — 08:29 PM
Shadow Meter Bulb
I think after all has been said, I will use the same bulb that is specified for the dial pilot light which is a #55. I ...georgetownjohn — 07:31 PM
12' Philco
There was also this Philco! klondike98 — 07:25 PM
HiFi (Chifi) tube amp build - but my own design.
I expected a challenge and this is just part of it. But, it's also supposed to be fun, entertaining, informative and enj...TV MAN — 07:12 PM
Shadow Meter Bulb
Butting in here with a question. Since the shadow meter is connected directly to the 1st and 2nd I.F.'s wouldn't the met...RossH — 06:43 PM
HiFi (Chifi) tube amp build - but my own design.
Mike, Tim; you are about to enter the twilight zone. Doo doo doo doo, doo doo doo doo This is something alright. I'm go...RodB — 06:26 PM

[-]
Who's Online
There are currently no members online.

>