1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Test Equipment
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
superior tv-11
sam
Phorum Expert
*****
Posts: 2,570
Threads: 336
Joined: Jun 2013
City: lawrenceville nj
#1

05-20-2014, 12:43 PM
hey guys
I received this was recapped at one point was suppose to work but nope did not I reflowed solder to cap and resistor that come loose it worked only problem is line adjustment will not center will not gou past 30
their is a cap old one with red strip ? schematic say`s should be a 20k and 47k is this a resister never see this before

http://www.radiomuseum.org/r/superior_tu...tv_11.html
[Image: http://i1303.photobucket.com/albums/ag14...a4c03a.jpg]
[Image: http://i1303.photobucket.com/albums/ag14...61117b.jpg]
thanks sam
Find
morzh
Odobenus rosmarus
*****
Posts: 15,444
Threads: 539
Joined: Oct 2011
City: Jackson, NJ
#2

05-20-2014, 01:26 PM
Sam

do you have a sch? Or a link? that is, not a Radiomuseum one?
Find
TA Forbes
Deviate Emeritus
*****
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
#3

05-20-2014, 08:59 PM
Without researching the part number, I believe that item is a Federal Selenium Rectifier Diode.
Find
Carl Travis
Member
***
Posts: 205
Threads: 6
Joined: Jun 2006
City: Moundsville State, Province, Country: WV
#4

05-20-2014, 10:29 PM
1159 is a good Federal selenium rectifier number.
Here's a manual, but it doesn't appear to match what's pictured:
http://bama.edebris.com/manuals/superior/tv11/
Carl
Northern Panhandle, WV
Find
sam
Phorum Expert
*****
Posts: 2,570
Threads: 336
Joined: Jun 2013
City: lawrenceville nj
#5

05-21-2014, 10:42 AM
hey guys
sorry morzh didn`t realized RM cut photo
I have same one carl put up thanks carl
it is a Federal Selenium Rectifier Diode 1159 but it dose not give any spec`s schematic says 20k
sam
(This post was last modified: 05-21-2014, 11:10 AM by sam.)
Find
Carl Travis
Member
***
Posts: 205
Threads: 6
Joined: Jun 2006
City: Moundsville State, Province, Country: WV
#6

05-21-2014, 02:24 PM
Sam,
The rectifier is marked 8Y1 on the schematic.
The item marked 20K is an adjustment pot.
Carl
Northern Panhandle, WV
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Test Equipment