Victor model R-7-A tombstone.
Posts: 2,035
Threads: 367
Joined: Jun 2010
City: Dover, OH
And the radio that won my money today is... this! Actually does work, but had a very amatuer restoration done to it years ago. This is the Canadian version of the RCA R-7-A using eight tubes with push-pull 47's. Gets quite loud and sounds pretty good. Only issues are that the dial control slips, the speaker wires are patched together, and of course it has the wrong knobs. Also, I think it will get an alignment in the near future as I want to give it a clean bill of health and correct the visible issues before using it much. This thing weighs about as much as my Majestic 20/21 tombstone, though is in much better shape. I would think the performance between the two would be similar.
No matter where you go, there you are.
Posts: 1,114
Threads: 14
Joined: Feb 2013
City: Irvington, NY
Dial drive on these is a problem. It uses a rubber grommet on the tuning knob shaft to rotate the dial. The rubber hardens and dries out, causing the drive to slip.
As I remember, I wrapped some black friction tape on my grommet to restore operation. Not the best solution but ti seems to work.
I have the earlier R-7 with the P-P 45's.
Posts: 4,876
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
That was something that they did in Canada for a while, they sold the same sets under the RCA and the Victor name plates up until 1934-35 or so. The chassis is likely identical to the one in my C.G.E S42-A, the S42 used push pull #45s, the S42-A used push-pull 47s and had a number of component value changes to go along with it. These sets used a potted can for the bypass condensers, but it used a pair of Mershon wet electrolytics for filter condensers, the output transformer and the audio interstage are potted inside the larger can. They also use a multitude of B.E.D code dog bone style resistors that will need to be checked and likely replaced. If you need the service data I have the info printed out of the Canadian G.E manual, including the parts list.
Regards
Arran
(This post was last modified: 05-22-2014, 11:09 PM by Arran.)
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
The R7A is TOUGH to restore. Take your time and diagram everything.
Posts: 2,035
Threads: 367
Joined: Jun 2010
City: Dover, OH
Thanks, I will be careful. It looks like most of the heavy work has already been done. Won't know until I pull the chassis though.
No matter where you go, there you are.
Posts: 4,106
Threads: 310
Joined: Nov 2013
City: Kings Park NY
Cabinet looks like a strait shot to restore. keep us updated. If you don't want the crosley knobs let me know.
Kirk
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Posts: 4,876
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
Yes, I was going to mention that, the original knobs were just some generic looking wood knobs, with domed ends, no carving.
Regards
Arran
Posts: 2,035
Threads: 367
Joined: Jun 2010
City: Dover, OH
I would gladly donate the Crosley knobs.. heck I could use two of them myself! Sadly, all three have been broken and glued back together. I was wondering about the wooden knobs. Generic I can work with! 
No matter where you go, there you are.
Posts: 893
Threads: 9
Joined: Mar 2008
City: Vieques, PR USA
State, Province, Country: PR
Jayce, take a look at Ed's knobs. p/n KRCA11. renovatedradios.com
Posts: 2,035
Threads: 367
Joined: Jun 2010
City: Dover, OH
Thanks! I'll give that a check tomorrow!
No matter where you go, there you are.
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
Philco 46-480 Electronic Restoration
|
| Haha, thank you sir! I’ve been eyeballing a 47-1230 console for sale over north of Bentonville, Arkansas for a while. Pr...jrblasde — 09:18 PM |
|
Philco 46-480 Electronic Restoration
|
| @ Joseph, get off the porch and run with the dogs. You fixed one, grab another. @ Morzh, I think that we are the same ...MrFixr55 — 08:59 PM |
|
Philco Model 249 made in England
|
| Wow! Now that is something! I’ve never seen a Philco like that, but it’s pretty mid-century.jrblasde — 06:40 PM |
|
Philco 46-480 Electronic Restoration
|
| I've run the radio for a couple of hours today, and all is well. It's a remarkable sounding radio! I'll go ahead and upl...jrblasde — 06:05 PM |
|
Philco Model 249 made in England
|
| Gary - Thanks for responding! I hadn't actually taken possession of it at the time of my post but since you said it was...fklown — 03:32 PM |
|
Philco model 40-100
|
| Marion;
Replacing volume controls was something some service shops did in years gone by to make a little extra profit...Arran — 03:24 PM |
|
Philco Model 249 made in England
|
| Welcome to the Phorum, fklown! That's one heck of a Philco 'yardstick' you've got there! Could you possibly post a clo...GarySP — 03:19 PM |
|
Philco model 40-100
|
| Arran,
Thank you so much for your assistance and the link to the fleabay listing! They say a picture is worth a thousan...mhamby — 01:43 PM |
|
Philco Model 249 made in England
|
| I wonder if anyone has any information or experience with this model. My internet searches are coming up with nothing. ...fklown — 11:40 AM |
|
Road Trip for a Philco 46-480
|
| Good morning, folks! I’ve finished the cabinet and the electrical restoration, and have detailed those in their respecti...jrblasde — 10:56 AM |
|
Who's Online
|
There are currently 479 online users. [Complete List]
» 1 Member(s) | 478 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
