Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Mikes 70 DONE
#16

Kirk, I think you are on the right track. A couple of coats of sanding sealer followed by the toner should do it.

Steve

M R Radios   C M Tubes
#17

Thanks Steve,
I went to buy it and boy has it gotten expensive. I took 4 years to use the last can so I think I will get my moneys worth.Icon_lol

Kirk

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#18

Today I unclamped the base and it is nice and strong. If I dropped it off the 2nd floor it would survive. well, the base would...

I glued and clamped all the separations from the arch and the sides and tomorrow I will sand to remove any excess glue and grain fill the arch and molding on the front.


Attached Files Image(s)
   

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#19

Kirk,
That is quite a job you are doing. I expect you will start getting inquiries regarding rrefinishing other radios.
Thanks for sharing,
Henry
#20

Unclamped the cabinet for the final time. I was going to grain fill but I found a veneer issue I didn't want to leave.


Attached Files Image(s)
   

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#21

GRAIN filler!!

Grain filler was finally applied to the cabinet! I stripped the molding and put sanding sealer on it. Will tone tomorrow.

All veneer is fixed, the entire cabinet is glued and solid. Faca and grill are completed.


Attached Files Image(s)
       

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#22

Toning day,
Taped off the columns and toned the inside grooves Ex Dk Walnut.

Then toned the entire cabinet with a medium walnut. I want to let the lacquer set for a day so I can sand the cabinet before clear. Too much dander in the air and the finish is not smooth.


Attached Files Image(s)
       

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#23

Take your time Kirk, no rush Icon_smile
#24

Today was rebuilding day. I took the freshly toned molding and attached it back on to the cabinet with the original nails and added some glue. I filled any crevices and the countersunk nail holes and tomorrow I will finish toning the trim, Put the face back in and clear clear clear...

In about a week I will finish sand and wax her up.


Attached Files Image(s)
       

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#25

Can I say...........JUST BEAUTIFUL!!
#26

Bad start to a day!
Finished toning and Untaped to reveal pulled up finish and perfect brown seeped under the tape. Have to strip and re-start.


Attached Files Image(s)
   

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#27

Bad Perfect Brown! Bad!
#28

Ok I finally got it right. Icon_crazy

I toned the front and then cleared 6 good coats. Sanded 400-2000 and will wait a day or so for the cabinet finish to harden. Then I will Apply some pumice and rub out the cabinet. Since it is a high gloss finish I will rub it out again with lemon oil and then wax her.


Attached Files Image(s)
       

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#29

And you people were serious when you told me that I could do all this!
I would probably retire by the time I finished it.
#30

Well I buffed her out with oil and cloth and then added 6 coats of wax.

I re-assembled her and now to let the wax harden for a week or so.

   
   
   
   

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Usually a wave trap is for keeping IF signals from entering the antenna and from leaving the antenna. You feed an IF sig...RodB — 09:30 PM
Philco 60 Squealing
I just peaked it for the best signal at 600. NULL it for IF frequency, originally it would have been null for 500kh...Chas — 08:05 PM
Philco 60 Squealing
Wavetrap no longer matters.morzh — 05:19 PM
Philco 60 Squealing
Rod, I had checked out your suggestions but did not help. I did solder the ground rivets to the chassis as Chas suggeste...dconant — 04:52 PM
37-690 Bass Choke Replacement
Yeah, I know, Mouser and Digikey don't have "big iron" components. For some reason Philco was messing with the...Radiodial — 04:25 PM
37-690 Bass Choke Replacement
Yes, I just had to deal with that while repairing the 37-604 Philco. Exactly that value choke was gone. And the current ...morzh — 03:52 PM
37-690 Bass Choke Replacement
Ah, now where to find one. I've into this before on smaller sets, I now recall. Hammond makes one that is only rated...Radiodial — 03:27 PM
Philco 38-7 Speaker
Ask the admins to put them together. As for the renaming, while inside the thread, you simply press "New reply&quo...morzh — 02:23 PM
37-690 Bass Choke Replacement
This is the parts catalog. 32-7528 choke is 65H, 10mA, 2,250 Ohm inductance. Find a suitable one.morzh — 02:18 PM
37-690 Bass Choke Replacement
While troubleshooting the no bass amplification issue, I think I found the culprit. The choke #104 is reading 164K ohms....Radiodial — 01:42 PM

[-]
Who's Online
There are currently 3672 online users. [Complete List]
» 1 Member(s) | 3671 Guest(s)
Avatar

>