Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

#80 tube
#1

If the numbers on TV 7 tester are being 48/53, is the tube still operational? Thanks.
#2

What does the chart say they should be?
As long as the tube shows both halves conducting, even below Good, the tube will work, even if a bit weak.
Both halves should be close in value though or you will sustain increased hum.
#3

Put it in your radio. If it works, it's good.

Steve

M R Radios   C M Tubes
#4

I see.But have to buy it prior to that.
#5

Agree. try it. Readily available and inexpensive, shouldn't be much of a gamble.
#6

As long as there is no short between A and K and tube shows some conductivity the radio s the best test. If it works, it works.
#7

Is this a used #80 you are thinking of buying? I have no idea what those numbers were that you quoted? Percentages? I would not buy an #80 tube that was marginal, good used ones are too easy to come by, but if it were in a radio it would still be usable.
Regards
Arran
#8

http://www.ebay.com/itm/HERE-ARE-4-TYPE-...3f3743ca0e

I think this is the auction.
I think they are OK tubes.

Why, you think a guy with 100% rating will knowingly push bad nonworking tubes?
#9

I've always heard that rectifier tubes are either good or they are bad. Basically, they either work or they don't. I don't know why, but the tester I used to have and others always show one side of an 80 as being weaker than the other. 48/53 isn't a big split and that tube should last a good while longer. If one radio doesn't like it, another one of your radios might. I've had that happen as well.

No matter where you go, there you are.
#10

Jayce

I believe 80 has a structure that makes measurement asymmetrical, hence the different scale factors when looking at English scale.
#11

Well when it is all said and done with the tube in the set working just measure the B+. If it is within 20 percent of the listed voltage your good to go.
Terry
#12

Just got back home and read all posts.Thing is, I just need 2 globe 80's so the radios look proper in appearance, otherwise
I have a number of non globe working 80 tubes.Thanks for the info.I might even get them as a gift along with some other stuff (Father's Day).




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
38-10T chassis Restoration begins
Thanks for the info guys. I always wondered why the use of mica. Now I know.dconant — 01:52 PM
38-10T chassis Restoration begins
Most common plastics have a dielectric constant in the 3-4 range whereas mica is around 6. This means that even if you w...Steve D — 01:46 PM
38-10T chassis Restoration begins
It is acceptable but not desirable. Plastic is not an approved cap dielectric, and even though a reasonably thick piece...morzh — 11:52 AM
38-10T chassis Restoration begins
I have a question about the mica sheets. I thought I saw somewhere on the Phorum where someone used thin plastic report ...dconant — 10:44 AM
38-10T chassis Restoration begins
Yes, you should carefully remove the mica sheets from the trimmers otherwise you risk trapping foreign material in the t...RodB — 10:34 AM
American Bosch Model 802 auto radio
Hi Joe, Thank you again. The American Bosch Model 634A has the same tube lineup as my Model 802 and the parts layout dia...Antipodal — 03:09 AM
38-10T chassis Restoration begins
hello everyone, I know it has been a while since I have posted about this radio but finally got chance work on it . I ...radiorich — 02:45 AM
Rusty Tuning Condenser
You could soak the fins in vinegar. You have to be careful if any pot metal is involved because the vinegar will dissolv...RodB — 09:20 PM
Rusty Tuning Condenser
Hello, I have a Philco 91 where the tuning condenser fins are rusty. I magnet sticks to them so they can't be aluminium....dconant — 05:50 PM
American Bosch Model 802 auto radio
I’ve found six United Bosch auto radio’s with the same 6-tube line-up as the 802, on NostalgiaAir. They are models 150, ...Joe Rossi — 02:52 PM

[-]
Who's Online
There are currently 3738 online users. [Complete List]
» 4 Member(s) | 3734 Guest(s)
AvatarAvatarAvatarAvatar

>