Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Milk House Philco
#1

Dad and I decided to visit a family we know to check out some antique tractor parts he had been offered. While there on the old farm, we mentioned our trip up to Mentor, Ohio yesterday to pick up an old radio and remembered one he had stored away in the old milkhouse a couple years back that his wife's relatives had never come around to claim. Apparently it had spent most of it's life in the attic of an old house in town and he said it was pretty filthy and the push-buttons were all broke. He asked if I wanted to see it and I said yes, of course, and what I discovered was a Philco 39-40 console that was indeed filthy, but a definite diamond in the rough. After talking it over with his wife, I nabbed the radio for $60 and even found the mostly intact owner's manual laying inside. After an initial cleaning (sooty with a helping of muddy cat paw prints) it is looking pretty good! Buttons are toast though, as is the cord which fell off.

   
   
   
   

No matter where you go, there you are.
#2

Nice find! Nice price!
#3

It's in good shape.
#4

Great find.. And the cabinet and grill cloth look nice.
#5

Icon_thumbupIcon_thumbupIcon_clapIcon_wave
#6

Thanks! I have never really pursued these style Philcos before, but this one was just in too good of shape and the price was right. Now, I will need new pushbuttons for sure and I think this model used the transluscent 'wine' color buttons. Kinda hard to tell as my buttons have degraded down to flakes, literally! Also, what would be the best way to get the green tarnish off the bezel? I have some Brasso, but I don't want to go too far and lose all the patina.

No matter where you go, there you are.
#7

Very nice find, Jayce! I might have a set of the repro wine buttons around here, actually.
#8

Amazing...you never know.
#9

Depending on the year the dial escutcheons on those sets could be bright brass, painted a gold colour, or have a faux wood grain.
Regards
Arran
#10

For 1939-1942 Philco escutcheons with thumbwheel controls:

I think the 1939 model escutcheons are brass. The 1940 escutcheons are brass plated (or painted) steel. The 1941 and 1942 escutcheons have the faux woodgrain.

--
Ron Ramirez
Ferdinand IN
#11

Unless they used up stock from the previous year, the escutcheon they used on my 40-780 was brass, I do not know if it used to have paint on it or no. Bob Andersen's 39-30 was brass but was painted with metallic gold or brass paint rather then bright brass. Neither of these sets used the thumb-wheel knobs however, so the thumb-wheel knob sets like the 39-116 may have been different.
Regards
Arran
#12

I decided to do the magnet test and the little magnet I used will not stick to the escutcheon on the 39-40. So, it is probably brass. As far as any paint goes, that is had to tell, but I have so much crusty green tarnish sticking up that I will have to do cleaning no matter what. Now, the escutcheon on my 40-180 looks like brass, but the magnet sticks right to it.

No matter where you go, there you are.
#13

Check the top corners of the openings where the buttons came through... If there was paint there, that's the most likely place to find any remains.

Pretty set! and the GRILL CLOTH all intact... Unusual.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM
Made mistake & did not label connection
You'll have to forgive me, I am not sure what you mean.  Can you explain what you are really saying.  If anyone does not...georgetownjohn — 08:05 PM
Made mistake & did not label connection
Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM
Made mistake & did not label connection
Maybe this is starting to make some sense in my hard head.  Is this why the wire in question was not in the great Ron Ra...georgetownjohn — 04:34 PM
Made mistake & did not label connection
I was correct with the 6A8 pin connection's, 7 and 8 are connected to ground as well as the tube shield (the broken line...RodB — 02:41 PM
Made mistake & did not label connection
What does the dotted line representing that surrounds the tube in the schematic?georgetownjohn — 02:17 PM
Made mistake & did not label connection
Hello John, I have been there either label got lost or was not labeled ! Sincerely Richardradiorich — 02:15 PM
Made mistake & did not label connection
Sorry, it is a Philco 37-640.  Does that help?--Johngeorgetownjohn — 02:14 PM

[-]
Who's Online
There are currently no members online.

>