Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

#16

Yes, that Alton. He only sells tubes that test close to or at NOS Gm. In fact, I need to ctc him as I have not done so in awhile.

I prefer using a grill to make s'mores. Tried using high current through a resistor and it made them taste funny.
#17

You had better contact him quick, Tom...he had placed an ad in ARF wanting to sell his business, and then withdrew it:

http://antiqueradios.com/forums/viewtopi...5&t=253556

--
Ron Ramirez
Ferdinand IN
#18

He's been saying that for years, but maybe I'd better.......
#19

Crying "wolf," eh? Icon_think

--
Ron Ramirez
Ferdinand IN
#20

HA! Ya I believe where Alton is from in "Loo-ziana" they call it "cryin'-wuff"
#21

Gary did that too on his website.. oldradioparts.com.. posted it was for sale and then it disappeared after he took a little vacation.. hehe..
#22

Actually, I can understand that...one can experience health issues, or simply get "down" about things and want to quit, and then realize that he or she enjoys the work and decides to keep going.

I do not know Alton but I wish him well.

--
Ron Ramirez
Ferdinand IN
#23

Hoo-boy, can I attest to that! The older you get the harder it is to fight all the health issues. Old age ain't for sissies!!
#24

Alton's a nice guy. He automatically sends me Philco Tubes whenever I make an order. ;-)

btw... still fighting this 39-7.. I have a short somewhere... it's pissing me off cause I can't find it.
#25

Try leaving a cold solder joint in a mouse trap. It attracts shorts.... Icon_smile
#26

If you know there is a short, it is easy to find. A short is a short. Especially a dead one.
#27

it's not a dead short. Icon_sad I'm going to bring it to the next VRPS meeting.. need a fresh pair of eyes. I know it's staring me in the face but I'm not seeing it. maybe I should go post something in the electrical restoration section as well.
#28

Maybe you should Icon_smile




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Samlex heavy-Duty bench supply filter question
Hello Everyone, I have one of my Heavy-duty bench powersuplies made by Samlex it's 13.8 volt dc 20-25 amp supply. What I...radiorich — 11:24 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
It's a Glaser Sears changer which Philco's engineers thought was an upgrade over a VM, but in retrospect I'd prefer the ...jeibner — 10:39 PM
AC/DC Transformer-less Sets
Joseph, Thank you for the confirmation. I knew that there must be more to the Transformer-less AC/DC radios than the ...PeterN — 10:30 PM
AC/DC Transformer-less Sets
Good evening, folks. Power station engineer here! The east coast had pockets of DC-only power well into the twentieth...jrblasde — 10:11 PM
AC/DC Transformer-less Sets
Model 40 does not have a rectifier, so it would be a DC only model. This however does not say anything about using...morzh — 08:01 PM
AC/DC Transformer-less Sets
I was wondering if anyone knows if these AC/DC transformer-less sets were actually used on 110v DC anywhere, and when. ...PeterN — 06:35 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
Given the 1960s vintage, it is likely that the cartridge is ceramic, likely more stable. The changer looks like a Voice...MrFixr55 — 05:03 PM
Jackson 665 j2 schematic request
FIXED!daveone23 — 03:55 PM
Bakelite crack repair - what is best epoxy?
Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM
Jackson 665 j2 schematic request
Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM

[-]
Who's Online
There are currently 6397 online users. [Complete List]
» 2 Member(s) | 6395 Guest(s)
AvatarAvatar

>