Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Fogged clear
#1

Here's a new problem that I've come across now that the weather is warm enough to spray. I'm using Mohawk Ultra Flo Clear Lacquer and obviously the humidity is too high because I'm getting some large fogged up spots.
Does anyone know what humidity is best for spraying clear? Right now at 9:15pm it's at 80%!
Thanks,

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org

#2

70% is about the absolute maximum. Some brands are a little more tolerant than others.

Steve

M R Radios   C M Tubes
#3

Eric, get some Mohawk No Blush Plus. Just a small spray will eliminate the fog. One can will last a loooonnnnggg time. Icon_thumbup

--
Ron Ramirez
Ferdinand IN
#4

Thanks, Ron. I just put an order in to AES for 2 cans. Icon_clap

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org

#5

So you apply it after you spray clear, or before, or when you get fog to eliminate it? How's it work?
#6

If you spray lacquer (whether it is toner or clear) and it comes out with a milky appearance, a quick spray of No Blush Plus will make the milkiness (blushing or fog) instantly disappear.

It doesn't take much, which is why one can will last a long time unless you are spraying lots of cabinets every day in high humidity.

And No Blush Plus is clear, so it can be used to correct blushing (fogging) on toner or clear.

--
Ron Ramirez
Ferdinand IN
#7

Which tells me that the milkiness then is purely surface phenomenon, the top surface forming into something not as smooth as it is supposed to be and the No Blush makes these wrinkles disappear. Otherwise it wouldn't help, were it structural and not surface.

Good to know.
#8

Steve Davis Wrote:Some brands are a little more tolerant than others.

Great point, Steve. Deft lacquer spray was very tolerant of high humidity.

Notice I said was, past tense. I went to Lowe's recently to stock up on Deft only to find that they no longer carry it. I went to the Deft website and it appears they no longer make it in spray cans. Icon_evil Icon_evil Icon_evil Icon_thumbdown

I really want to say something political...I really want to say something political... Icon_evil

But I think you can read between the lines here.

--
Ron Ramirez
Ferdinand IN
#9

Be careful Ron, I hear these new Super Moderators are pretty tough!Icon_wave

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org

#10

wow.. I usually use the ultraflo when it's more humid to avoid blushing. how humid was it? Mohawk recommends not to go above 65% or below 65 degrees. however, Bob Anderson did a video on one of his tombstones. seemed that around 55-60 the lacquer stayed fluid just a little longer and flowed out better.

that super blush retarder is wonderful stuff. just the lightest misting is needed. it disappears before your eyes like a TV commercial
#11

Quote:Notice I said was, past tense. I went to Lowe's recently to stock up on Deft only to find that they no longer carry it. I went to the Deft website and it appears they no longer make it in spray cans. Icon_evil Icon_evil Icon_evil Icon_thumbdown

Our local Lowe's no longer carries Deft at all. As a mater of fact, they no longer carry lacquer of any kind. Menards has Watco brand in quarts, gallons and spray cans. Their price is right too, a gallon is $24.99, which is the lowest I have found. We also have two Walmart stores close by. They both have Minwax lacquer in spray cans.

Steve

M R Radios   C M Tubes
#12

The Penguin is watching……

[Image: http://oi39.tinypic.com/mrs60w.jpg]
#13

I did a little research and it seems to be a decision by Penguin Paints who bought out Deft in 2013.
#14

We still have Deft at Home Depot and ACE, last time I checked. It is marked now as "brushing lacquer". I asked about that and the salesman indicated that due to VOC problems with reducing it with lacquer thinner they had to label it that way. It works fine reduced and sprayed. I don't use rattle cans and mix my lacquer with dye for toning.
Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#15

Jeez. I switched to Deft because it covers and finishes acceptably and the physical spray nozzle is superior.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently 3966 online users. [Complete List]
» 2 Member(s) | 3964 Guest(s)
AvatarAvatar

>