Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

37-116 and 118
#1

Well,

have just return from the trip to Hartford area where I
1) picked up 37-116 (the one that is going to Ukraine) or $175, and
2) 118, the same one I was denied the sale of first.The price came out to be 160.

Photos later, I haven't eaten since I had breakfast 8am.
#2

I am happy that the guy decided that you were good enough to buy it from him.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#3

Yeah, I am much better in person than in my emails, Kirk can attest to that Icon_mrgreen
And thick Russian accent helps. It is cute.
#4

Wow .... I look forward to the photo ...Icon_thumbup
#5

I can show it to ya 'morrow morn, if you pick up Skype call about 2 pm your time.
#6

2am .... So this stuff. For your favorite receiver is ready for such a small sacrifice ... I hope that Google translator correctly translated my positive emotions ...
#7

No it did not.

Anyway, will show it to you tomorrow.
Now we'll have to figure out hot to get ot to you.
Ain't gonna be cheap, I could tell.

Will need to ask a UPS store to pack it, it is above my abilities.
And buy a piece of plywood to screw to the bottom of the chassis.
Will probably leave the speaker and clarifiers in the cabinet.
I will also take off the dial and the band light indicator wheel, put it ia a padded envelope and tape it inside the cabinet.
#8

Bought the chevron cloth from Kenny.
He promised to throw in two smaller pieces with centered center-line for the clarifiers.

Soon as it comes, I will ship the radio.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Help with Readrite 410 tube tester
I fixed it. The filament selector switch is not that great of quality. Cleaned it and it takes some fiddling with to get...daveone23 — 06:58 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
It's a vacuum tube set and it's over 60 years old.  My uncle acquired it for my parents when Philco was done with it, an...jeibner — 10:24 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
Hi J Eibner, Welcome to the Phorum.  Lots of Phriendly Pholks with Phine (See a pattern here?) advice. It is very...MrFixr55 — 09:54 PM
Philco 89B code 123 newbie
Or you can do what Terry suggests. Thx Terry for remembering that. A lot cheaper. I remember an article about that, b...MrFixr55 — 09:07 PM
Philco 48-200 alignment questions
Thanks to everybody for all the info so far. RodB, thanks for the additional info. I worked on this radio years ago a...transitony — 08:40 PM
Philco 89B code 123 newbie
Now that I've been thinking about it somewhere I saw a replacement made using a section of pvc pipe and a cap to cover t...Radioroslyn — 08:25 PM
Philco 48-200 alignment questions
Terry's gimmick cap is two insulated wires twisted together about 2 inches long, one wire attaches to the generator outp...RodB — 07:46 PM
Philco 48-200 alignment questions
Hi, in this case I would be certain that pin 7, which is B-, of the 14A7 is not "hot". If it is then reverse t...RodB — 07:39 PM
Philco 48-200 alignment questions
Yup. The gimmick is to take the place of the 100mmfd cap you don't have.Radioroslyn — 07:34 PM
Philco 48-200 alignment questions
Thanks for the reply Terry. Yes I am definitely using an isolation transformer. If I work with your method and connec...transitony — 07:29 PM

[-]
Who's Online
There are currently 684 online users. [Complete List]
» 1 Member(s) | 683 Guest(s)
Avatar

>