Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Speaker repair
#1

Part of my 16B 11"speaker's back is covered with a some sort of gauze material, and, needless to say, had a better days.What is the purpose of it? Is it for the audio base improvement? How important is it and what kind of material one should use for replacement? Thanks.
#2

If you mean this cobweb style on top openings, I think it is simply to prevent dust accumuation. Radio is oen (unlike close speakers today) and dust fall from above.
#3

Some manufacturers made it a practice to add screening or gauze material to the speaker basket area behind the cone. This kept debris out of the back side of the speaker and gave some degree of protection to the speaker cone along with the front grill cloth. Hopefully people would not make a practice of poking around inside their radios. Unfortunately many early radios had no back cover at all.

There were very few speaker arrangements that incorporated any sort of enclosure in the early years of radio. The appearance of Altec speaker/enclosure combinations for theater sound systems were an early example of bass reflex enclosures. You can do an internet search on loudspeakers and find a wealth of information on the subject.

Joe
KC5LY
#4

Joeztech,

I see your point. However, not only on my set, but on many others the gauze covers only 1/2 of the basket and only the right side of it looking from the back, having the left one open(?)
#5

Fields100, the speaker is mounted in the cabinet wrong, the gauze was meant to be on the top, not to the left or right, to prevent dust and debris from settling into the voice coil.

Gregb
#6

Gregb

All respectable sites on the web to name a few show the gauze on the right side looking from the back.I agree with you, it is only one logical way for it's location and, honestly, I would not feel bad putting it on the top, on the bottom or just omit it whatsoever, there are other things more important to be concerned about. It just very curious. There must have been the reason for it.
Thanks.
#7

Well maybe I am mistaken, but it seems logical that it would be on the top. Maybe Ron might know one way or the other.

Gregb




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM

[-]
Who's Online
There are currently 4924 online users. [Complete List]
» 1 Member(s) | 4923 Guest(s)
Avatar

>