Crosley 124 amperage draw
Posts: 1,475
Threads: 69
Joined: Nov 2012
City: Kansas city, MO.
I just recapped and changed some out of tolerance resistors on this 124 Crosley. I always bring up on variac with amp scale in line.
Most of the radios I have done read about .5mA on 3amp scale.
This one is reading .85mA seems high to me.
Does anyone know if this would be a normal range for this radio?
I was at 120v on variac setting. It does play pretty well but I turned it off because of high amp reading. Thanks
Posts: 15,527
Threads: 545
Joined: Oct 2011
City: Jackson, NJ
Does not make sense, normal draw will be in over a hundred mA.
Are you measuring DC or AC amps? And is your ammeter Ok and the fuse inside it good?
Posts: 1,114
Threads: 14
Joined: Feb 2013
City: Irvington, NY
Mike probably means .5A and .85A which would make more sense on the 3A scale.
These readings would seem reasonable, depending on the tube count of the radios involved.
Posts: 1,475
Threads: 69
Joined: Nov 2012
City: Kansas city, MO.
I have a 3amp and 7 amp ac ampere meter guage that is in series with the variac outlet that I plug the radios into. It is wired to the 3amp scale. I might be stating the reading wrong.
When I said .85mA I mean that it is almost at the 1amp on the scale. Most of my other radios read right at .5 half way btwn. 0 and 1 amp.
Posts: 1,475
Threads: 69
Joined: Nov 2012
City: Kansas city, MO.
Mondial you are correct. I was going to take some tube voltage readings but did not want to do this if the current was too high. Back to the books on amperes and how to properly determine. Thanks
Posts: 1,114
Threads: 14
Joined: Feb 2013
City: Irvington, NY
I just looked at the schematic and the Crosley 124 uses a pair of 47's in push pull for the output. This radio will draw more AC current than a radio with a single output tube which you may be comparing it with.
Does the back of the set have a nameplate with the AC power consumption ( Watts rating) ?
Posts: 1,475
Threads: 69
Joined: Nov 2012
City: Kansas city, MO.
There is a plate that has the model number and next to it says 125 watts.
Posts: 1,114
Threads: 14
Joined: Feb 2013
City: Irvington, NY
If the radio is rated at 125 Watts, then the .85A current draw is not a problem. The amp current draw will be proportional to the Watts rating.
A radio rated at 60 Watts might show a .5A reading, but a 125 Watt radio will draw significantly more, close to 1 amp or more.
Posts: 1,475
Threads: 69
Joined: Nov 2012
City: Kansas city, MO.
Thanks Mondial. Going to check tube volts, do an alignment, and let it play awhile.
Posts: 15,527
Threads: 545
Joined: Oct 2011
City: Jackson, NJ
Let's try to call Amps Amps, Ohms Oms etc.
We are, after all, dealing with electricity and if someone wants to explain something and get help, it pays to be accurate in what one is saying about units.
Posts: 2,128
Threads: 18
Joined: Oct 2008
City: Merrick, Long Island, NY
Watts dat? Other than fusisters, little radios are ok with .5 or .75 amp, mediums 2 amp, and large 3 amps. If you know everything else is OK, you can move up a value if needed.
I've seen modern guitar amps with a 3 amp fuse in the holder on the back of the cabinet, and a 5 amp secondary inside. Sure enough user did the deed and kept upping the back one to keep playing. Fixed it did with a recap job etcetera, for about the same cost as a replacement amp. Wanted it back, he did, so I did as he asked. Mind you I only do favors and never made a nickel on repairs since I was a kid.
Posts: 15,527
Threads: 545
Joined: Oct 2011
City: Jackson, NJ
3 Amps...yikes. Nice space heater that radio would be....
Posts: 2,128
Threads: 18
Joined: Oct 2008
City: Merrick, Long Island, NY
Yup, humongous ones can do 3 big ones on turn on. Nice in a cold climate where you don't pay seperately for electric.
Posts: 15,527
Threads: 545
Joined: Oct 2011
City: Jackson, NJ
Turn-on current is the inrush, inductive type at that, won't do anything bad except blowing an improperly sized fast-blow fuse.
It's the steady one that will help you in North Dacota.
Users browsing this thread: 1 Guest(s)
|
Recent Posts
|
Correct model 84 Ac plug an cord type
|
From what I read Philco went to using brown rubber power cords in 1936, so cloth was used in the 1935 and earlier models...Arran — 11:25 PM |
Correct model 84 Ac plug an cord type
|
Hi Bruce,
I have not worked on an 84, but in general, power cords for almost any radio prior to 1938 was cloth covered...MrFixr55 — 08:34 PM |
Restoring Philco 38-14
|
OK, well, so after staring at the sch again, I realized the problem had to be the #12/12A padder.
I put a scope on the o...morzh — 08:15 PM |
Correct model 84 Ac plug an cord type
|
Hello Bruce,
I mostly use brown far as my cloth powercords go !
Here is the plug that I have used bakelite Acorn style...radiorich — 08:05 PM |
Correct model 84 Ac plug an cord type
|
Looking for as correct as can find the right Ac plug an the correct colored cloth line. Ive seen many old photos but mos...Bruce — 04:13 PM |
Restoring Philco 38-14
|
Rod
Two Y-caps make sense if you use them from L/N to the chassis; this is only makes sense in the transformer radios...morzh — 10:11 AM |
Restoring Philco 38-14
|
Mike, I'm curious about a specific use of he Y cap. Lately I've seen a single cap across the power transformer primary. ...RodB — 09:01 AM |
Restoring Philco 38-14
|
hello morzh ,
That sounds like a plan !
Sincerely Richardradiorich — 07:45 AM |
Restoring Philco 38-14
|
Richard,
It helped some, but I still had the whining when engaging the rear power strip (I did not realize it was fro...morzh — 07:07 AM |
Restoring Philco 38-14
|
Hello morzh,
Yes , that dreaded hum in my room where i do alighment I have my cable modem and router plus desktop plus ...radiorich — 11:25 PM |
Who's Online
|
There are currently 3861 online users. [Complete List] » 1 Member(s) | 3860 Guest(s)
|
|
|
|