Thread Rating:
  • 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 89/19 "before & after"
#1

        This 81 year-old cabinet turned out pretty nice. I used Mohawk toners and lacquer. The pretty wood grain on the front "came out" after I began toning. I wish it were mine but alas, I must return it to its owner next week.
Art
#2

Very nice job Art, the owner should be pleased.
Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#3

Well done!
Icon_clapIcon_clapIcon_clap
#4

Looks very nice.
#5

Icon_thumbupIcon_thumbupIcon_thumbup

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#6

Super job Icon_thumbupIcon_thumbupIcon_thumbup

Steve

M R Radios   C M Tubes
#7

Excellent work! Bravo!
#8

Super!
Love seeing restorations!
Before and afters are just awesome

Kirk

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#9

Looks great, Art.Icon_thumbup I'm still learning the fine art of refinishing. Did you use grain filler on this one?

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org

#10

Eric,
No grain filler on this one. No sanding either. Just strip, tone, and finish.
Art
#11

Thanks Art. I've got a 66B that I'm about to start on. What would determine if I need grain filler or not?

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org

#12

Eric,
I would go by feel and looking at it with a magnifying glass. I don't fill if I don't have to. I think it's a lot of work that is not always necessary. Sometimes it depends on the type of veneer. Some wood is more open than others.

I mean it's an old radio and doesn't need a piano finish IMHO. But I know people feel differently about this.
Art
#13

Thanks Art. I agree with you.

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org

#14

Really nice work !!
#15

Thanks all. It was nice to work on a cabinet that didn't require much repair. There was a very minor ding on the arch and a VERY minor area of missing veneer on the front curve that you can't even see in the picture and hard to see in person. Someone took good care of this radio. Too bad it was neglected the last several years. The chassis had layers of grungy dirt. The knobs are in excellent condition also and fit snugly on the shafts. I did not polish the escutcheon--just gave it a good cleaning. I hope the next one is as pleasant to redo as this one was.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Restoring Philco 37-604C
Hello mike, My Stand also has some very minor rust too and mine is used inside my heated house . Sincerely Richardradiorich — 11:02 PM
Philco 10 car radio head key
Hi Keandkafu, In general, the Key Code usually has nothing to do with the brand of key, but is a code for how the not...MrFixr55 — 10:37 PM
Radiola 18 Amplifier & PS
If the 2.25V winding is not being used, the center tap wire can be insulated by taping off.  If the 5V filament winding ...MrFixr55 — 07:33 PM
Hippo 46-420 Schematic doesn't match parts list.
Here you have the part in the sch with values. I am not sure what else is needed.morzh — 02:56 PM
Restoring Philco 37-604C
Ron Here are the two of my jigs side by side. They have been with me about the same time (a couple of month differenc...morzh — 02:05 PM
Kurt P
Terry, gotcha, thanks for the clarification.  That’s probably why the speaker seems shorted.  Assuming the OT/FC/speaker...Kurt P — 10:59 AM
Radiola 18 Amplifier & PS
I have the 2.25V and 2.5V information confused, and must look more carefully at the schematic and Hammond transformer in...TN Allen — 10:24 AM
Radiola 18 Amplifier & PS
Thank you for the information, it all helps, although understanding some of it takes time. One reason for doing the PS a...TN Allen — 09:42 AM
462ron
Hi Mike, the radio is coming along nicely but wow, you must have some serious moisture in your shop judging by the amoun...462ron — 06:29 AM
Restoring Philco 37-604C
Have rebuilt the can. The can had 4 caps in it, 2x16uF, 10uF and 8uF. I used a 15uF as the first cap, 22uF and 10uF ...morzh — 09:38 PM

[-]
Who's Online
There are currently no members online.

>