Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

An Idea Realized - The Philco Super 89
#16

Here is how the 32B cabinet looked once I completed repairs to the cabinet.

[Image: http://www.philcoradio.com/images/phorum...89_011.jpg]

And now, after the Behlens Extra Dark Walnut toner had been applied to the top, sides and trim:

[Image: http://www.philcoradio.com/images/phorum...89_012.jpg]

With any luck, this set should be finished tomorrow!

--
Ron Ramirez
Ferdinand IN
#17

Tonight after work I finished spraying lacquer on my 32B cabinet; and then after letting it sit for awhile, I added grille cloth, reinstalled the escutcheon, and installed the Super 89 chassis and speaker.

By way of review, here is how the 32B cabinet looked before I finished gluing it together:

[Image: http://www.philcoradio.com/images/phorum...89_005.jpg]

As you can see, the top is off. You can sort of see, if you look closely, that the left shoulder is also missing.

Imagine if you will:

* top broken off
* left shoulder broken off
* left front trim broken off
* two grillebars broken out
* upper quarter round trim above front panel missing
* wooden brackets inside cabinet that held the 32B power supply were separated from the left side of the cabinet

Now look at the completed set below.

[Image: http://www.philcoradio.com/images/phorum...89_025.jpg]

As I said before...it is not perfect...but considering the condition both chassis and cabinet were in...it's a pretty nice transformation, I would say.

This is already my favorite radio...because I brought both cabinet and chassis back from pure junk...and with the modifications to the chassis, this set will outperform any stock 89. Icon_biggrin

--
Ron Ramirez
Ferdinand IN
#18

Gotta say, good job Ron Icon_wink

-Brian
If you collect or are interested in antique telephones, please visit Classic Rotary Phones
http://www.classicrotaryphones.com/forum/index.php




Users browsing this thread: 5 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently no members online.

>