Philco 53C to strip or not to strip?
Posts: 4,108
Threads: 310
Joined: Nov 2013
City: Kings Park NY
I have here a fine looking piece of Philco history but I cannot decide whether to strip it or leave it.
I gave it the Gojo but the top left finish is gone. front and sides are great though.
Do I leave it original and just seal the top or should it be redone?
I like original but the top is killing it. I cant just redo the top because it all curves together.
Here it is:
Attached Files
Image(s)
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
Most people would probably leave it as is. You could touch-up the top, but it would take some custom tinting of the lacquer. Several coats then a wet sanding of the entire cabinet followed by buffing it out.
It is easy to make it look worse attempting this, but it is a common approach for photo finish cabinets and could also be used here.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Posts: 15,705
Threads: 551
Joined: Oct 2011
City: Jackson, NJ
I'd leave it alone on front and sides.
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
Kirk, if that is bare wood exposed on the top it appears to have a bit of color to it. I would put a small drop of lacquer on it and see what the color looks like. Perhaps they used clear lacquer on the top? If the color is close a touch up spray might help.
Jerry
A friend in need is a pest! Bill Slee ca 1970.
Posts: 4,108
Threads: 310
Joined: Nov 2013
City: Kings Park NY
I will try the lacquer first, then try to match it if that does not work.
If that does not work then I will just leave it for now. I like original and can always refinish it later
Thanks all,
Kirk
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
When I said , several coats, I meant on the area with the finish missing only. The tint would be to match the yellowing that has occurred to the original finish. BTW, yellow is not good, very little brown in gloss or semi gloss lacquer will do it.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Posts: 4,108
Threads: 310
Joined: Nov 2013
City: Kings Park NY
Yes I got that,
We will see how bad I screw this up
Kirk
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
Here is one I fixed using that process.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Posts: 4,108
Threads: 310
Joined: Nov 2013
City: Kings Park NY
I matched the color and have added the first layer of new Lacquer
Attached Files
Image(s)
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Posts: 4,108
Threads: 310
Joined: Nov 2013
City: Kings Park NY
I added a few more coats but was unhappy with the results. I added some toner to the area for a better match and it looks better.
Not happy with the dark color but I wll try sanding it a bit more and see what happens
Attached Files
Image(s)
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Posts: 2,572
Threads: 337
Joined: Jun 2013
City: lawrenceville nj
Come on Ron say it to Kirk
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
You are getting there. Now the trick is to not sand so much as to sand through the original finish. I would have used less toner.
Do you have a high speed buffer (not that Walmart orbital thing)?
Wait a few days before you try to buff it out.
It is going to look much better and still be close to original.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
(This post was last modified: 08-27-2014, 06:47 PM by
Phlogiston .)
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
Hay Kirk, you are getting there. A little sanding to get the darker area of toner down a bit. It still looks a lot better now than it did.
Jerry
A friend in need is a pest! Bill Slee ca 1970.
Posts: 4,108
Threads: 310
Joined: Nov 2013
City: Kings Park NY
Ok,
I have done the most I can without ruining the originality of the radio cabinet. I am not super excited about it but I like that it it still has that original look. We'll say that it gives it character.
Kirk
Attached Files
Image(s)
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Posts: 5,074
Threads: 269
Joined: Nov 2012
City: Bandon
State, Province, Country: OR
Users browsing this thread: 1 Guest(s)
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one.
Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station.
Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site:
klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard,
Thx for posting the schematic. As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr,
The Electro Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply?
The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM
Who's Online
There are currently 2201 online users. [Complete List ]» 2 Member(s) | 2199 Guest(s)