1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 53C to strip or not to strip?
OldRestorer
Electronic geneus
*****
Posts: 4,109
Threads: 311
Joined: Nov 2013
City: Kings Park NY
#1

08-25-2014, 11:13 AM
I have here a fine looking piece of Philco history but I cannot decide whether to strip it or leave it.

I gave it the Gojo but the top left finish is gone. front and sides are great though.

Do I leave it original and just seal the top or should it be redone?

I like original but the top is killing it. I cant just redo the top because it all curves together.

Here it is:


Attached Files Image(s)
               
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Find
Phlogiston
Radio-Fixer-Upper
*****
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
#2

08-25-2014, 12:48 PM
Most people would probably leave it as is. You could touch-up the top, but it would take some custom tinting of the lacquer. Several coats then a wet sanding of the entire cabinet followed by buffing it out.

It is easy to make it look worse attempting this, but it is a common approach for photo finish cabinets and could also be used here.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Website Find
morzh
Odobenus rosmarus
*****
Posts: 15,444
Threads: 539
Joined: Oct 2011
City: Jackson, NJ
#3

08-25-2014, 01:47 PM
I'd leave it alone on front and sides.
Find
jerryhawthorne
Phorum Expert
*****
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
#4

08-25-2014, 01:55 PM
Kirk, if that is bare wood exposed on the top it appears to have a bit of color to it. I would put a small drop of lacquer on it and see what the color looks like. Perhaps they used clear lacquer on the top? If the color is close a touch up spray might help.
Jerry
A friend in need is a pest!  Bill Slee ca 1970.
Find
OldRestorer
Electronic geneus
*****
Posts: 4,109
Threads: 311
Joined: Nov 2013
City: Kings Park NY
#5

08-25-2014, 03:56 PM
I will try the lacquer first, then try to match it if that does not work.
If that does not work then I will just leave it for now. I like original and can always refinish it later

Thanks all,
Kirk
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Find
Phlogiston
Radio-Fixer-Upper
*****
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
#6

08-25-2014, 05:34 PM
When I said , several coats, I meant on the area with the finish missing only. The tint would be to match the yellowing that has occurred to the original finish. BTW, yellow is not good, very little brown in gloss or semi gloss lacquer will do it.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Website Find
OldRestorer
Electronic geneus
*****
Posts: 4,109
Threads: 311
Joined: Nov 2013
City: Kings Park NY
#7

08-25-2014, 06:50 PM
Yes I got that,
We will see how bad I screw this up Icon_mrgreen

Kirk
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Find
Phlogiston
Radio-Fixer-Upper
*****
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
#8

08-26-2014, 12:01 AM
Here is one I fixed using that process.

   
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Website Find
OldRestorer
Electronic geneus
*****
Posts: 4,109
Threads: 311
Joined: Nov 2013
City: Kings Park NY
#9

08-26-2014, 10:23 AM
I matched the color and have added the first layer of new Lacquer


Attached Files Image(s)
   
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Find
OldRestorer
Electronic geneus
*****
Posts: 4,109
Threads: 311
Joined: Nov 2013
City: Kings Park NY
#10

08-27-2014, 05:05 PM
I added a few more coats but was unhappy with the results. I added some toner to the area for a better match and it looks better.

Not happy with the dark color but I wll try sanding it a bit more and see what happens


Attached Files Image(s)
   
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Find
sam
Phorum Expert
*****
Posts: 2,570
Threads: 336
Joined: Jun 2013
City: lawrenceville nj
#11

08-27-2014, 06:25 PM
Come on Ron say it to Kirk Icon_twisted
Find
Phlogiston
Radio-Fixer-Upper
*****
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
#12

08-27-2014, 06:46 PM
You are getting there. Now the trick is to not sand so much as to sand through the original finish. I would have used less toner.

Do you have a high speed buffer (not that Walmart orbital thing)?

Wait a few days before you try to buff it out.

It is going to look much better and still be close to original.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
(This post was last modified: 08-27-2014, 06:47 PM by Phlogiston.)
Website Find
jerryhawthorne
Phorum Expert
*****
Posts: 1,562
Threads: 56
Joined: Nov 2008
City: Sedona, AZ/Placentia/CA
#13

08-27-2014, 07:04 PM
Hay Kirk, you are getting there. A little sanding to get the darker area of toner down a bit. It still looks a lot better now than it did.
Jerry
A friend in need is a pest!  Bill Slee ca 1970.
Find
OldRestorer
Electronic geneus
*****
Posts: 4,109
Threads: 311
Joined: Nov 2013
City: Kings Park NY
#14

08-29-2014, 10:25 AM
Ok,
I have done the most I can without ruining the originality of the radio cabinet. I am not super excited about it but I like that it it still has that original look. We'll say that it gives it character. Icon_wink

Kirk


Attached Files Image(s)
       
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Find
klondike98
Phorum Moderator
******
Posts: 5,060
Threads: 269
Joined: Nov 2012
City: Bandon State, Province, Country: OR
#15

08-29-2014, 10:42 AM
Looks very good Kirk!!!
Icon_clapIcon_clapIcon_clap
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
« Next Oldest | Next Newest »




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
PT-6 antenna connections
Hi Bridcarl +1 on the others.  Pin 6 of the 7C6 is the AVC Diode so it is appropriate that that pin 4 of the coil con...MrFixr55 — 07:30 AM
462ron
Joseph, this is beyond awesome. A lot of thought and engineering went into this and you hit a home run! Now I must save ...462ron — 07:27 AM
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM

[-]
Who's Online
There are currently 4607 online users. [Complete List]
» 1 Member(s) | 4606 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration