Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

SW aerial
#16

Never tried 75ohm on short wave receiver. To transmit you need RG58 ie 2 meter band to Hf bands. Have used single long wire to receive also 300 ohm or 400 ohm ladder lead with diapole ant. For 300 ohm twin lead try amazon.com cost around 15 dollars for 100 feet. David
#17

ARRL Ant book now cost $50 not on my budget. Found another Ant book as a free pdf download looks to have lots of good info. May be over the top for just wanting to receive but a good read. David http://www.apparentlyapparel.com/uploads...n_carr.pdf
#18

So, finally, It is done. 20 ft above the grade, 60 ft in total length, 2 pieces at 30 ft each coming to the central insulator, connected to the coax, one end to the center, another to the shield. At the set- tried the center wire to the "A", shield to the "G". Reception is poor, worse, than 15 ft straight wire. When both (center and shield) connected together just before connecting to "A"- reception is as good as my 25 ft wire hanging on the bush, albeit the stations coming in quite louder.But selection is still the same.Is anything wrong? I have been getting plenty of stations prior to that, but thought the new contraption will provide even better results.
#19

Glad you have the ant up and running. Something to consider is time of day if I want to listen to OZ get up at 430 AM make coffee turn on short wave have a 2-3 hour window then signal is gone. Another thing just not that much out there to listen to the BBC does not send a signal to North America they are hard to find. Best time for listening is at night. Living in Fl. There is always Radio Havana some of there stuff is in english. Try the ham bands most signals SSB their are a few nets using AM. Also at night try AM band still a few high power stations out there. David
#20

I have a long copper wire the length of my house in the attic, its about 70 feet long. I am able to pick up everything that is on at the times I listen. Great, simple, cheap antenna.
#21

I pick up plenty if not more. Albeit not sure it is "everything". Hence larger, taller antenna has been installed.
Yet, the amount of stations stays the same as with a simple long wire.
#22

That is what is to be expected. What stations you receive will be more dependent on propagation conditions rather than the antenna. If the conditions of the ionosphere are not favorable you will get no long distance reception at all. A good antenna will increase the received signal strength, but it cannot provide reception if the signal is not there in the first place.
#23

Out in the work shop turned on my SX-130 to see what was out there just after 12 noon 9-19-14 was going thur the ham band on 40 meters found a net that I was able to listen to for 30-35 minutes keep fading in out every 5 minutes. The frequency was 7.251 mhz ssb. Total lost of singal around 12.40PM. My receiver is analog looked up ther frequiency on the internet. First time listening to these guys will try tomorrow just never know what you will hear. Ant 20 feet of wire about 15 feet above the ground my location 184 feet above sea level. David




Users browsing this thread: 5 Guest(s)
[-]
Recent Posts
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM
Made mistake & did not label connection
You'll have to forgive me, I am not sure what you mean.  Can you explain what you are really saying.  If anyone does not...georgetownjohn — 08:05 PM
Made mistake & did not label connection
Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM
Made mistake & did not label connection
Maybe this is starting to make some sense in my hard head.  Is this why the wire in question was not in the great Ron Ra...georgetownjohn — 04:34 PM
Made mistake & did not label connection
I was correct with the 6A8 pin connection's, 7 and 8 are connected to ground as well as the tube shield (the broken line...RodB — 02:41 PM
Made mistake & did not label connection
What does the dotted line representing that surrounds the tube in the schematic?georgetownjohn — 02:17 PM
Made mistake & did not label connection
Hello John, I have been there either label got lost or was not labeled ! Sincerely Richardradiorich — 02:15 PM
Made mistake & did not label connection
Sorry, it is a Philco 37-640.  Does that help?--Johngeorgetownjohn — 02:14 PM

[-]
Who's Online
There are currently 5937 online users. [Complete List]
» 1 Member(s) | 5936 Guest(s)
Avatar

>