Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

variable capacitor
#1

When cleaning the variable capacitor I have seen that has a broken horseshoe pin. 

This is a problem for the operation ?.

[Image: http://s22.postimg.org/o7yr0g7o1/080.jpg]

[Image: http://s28.postimg.org/m51faoyn1/081.jpg]

[Image: http://s30.postimg.org/7xrcwpof5/082.jpg]
#2

You are probably ok. It's used the ground the rotor . Just make sure that the other one is good and clean. Use a bit of DE Oxit to clean it up.
Terry
#3

Thank you very much.
I'll finish cleaning and I will use it well.
#4

Cleaning may well do the job. It might be possible to fabricate a new piece if you want to go further. If cleaning restores proper function you may want to just let it be. One of the set screws looks like the head is broken off and considerable rust is present on the others. Set screws can be a real pain to deal with. Use caution with any chemicals to make sure not to get any on plastic materials nearby.

Joe
#5

   



Apart from the horseshoe clips, these rotor plates need a bending tweak.
#6

Hopefully, that's just an optical illusion in the photo. Continue looking to the left bank of plates. It looks like the circumference of the plates ends right there.
#7

I think it is due to the photo angle. They look OK to me.
#8

The sheets are fine, it is the effect of the photograph.
I have cleaned the forks and facing down the defect.

[Image: http://s29.postimg.org/9pj1gs7pz/121.jpg]
#9

Looks sparkling!
#10

(10-10-2014, 08:20 PM)morzh Wrote:  Looks sparkling!

I know it would be a pain but I would grind off the rivets that hold the forks, clean all of the surfaces (especially the cap frame where the fork makes contact), and put it back together using screws.  There's an awful lot of oxidation on the frame and it could make for a very noisy and intermittent tuning.  A Dremel tool with a small grinding will quickly cut the rivets.  The whole operation should take less than ten minutes.

Pete AI2V
#11

If the rivet is removed for cleaning, after it has become to be riveted.

[Image: http://s28.postimg.org/xtgp7sffh/DSC_0342_1.jpg]




Users browsing this thread:
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 4017 online users. [Complete List]
» 1 Member(s) | 4016 Guest(s)
Avatar

>