Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 1 Vote(s) - 4 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Atwater Kent 40
#1

It was so nice and clean I couldn't resist. Found in a local antique mall. The E series speaker was there also and tested good, but they wanted $195.00 for the speaker by itself so I passed on that. 

[Image: http://i1319.photobucket.com/albums/t679...d840d9.jpg]
[Image: http://i1319.photobucket.com/albums/t679...11e547.jpg]

[Image: http://i1319.photobucket.com/albums/t679...f36b73.jpg]
[Image: http://i1319.photobucket.com/albums/t679...7d4481.jpg]
#2

The green resistor was added, and I think it is the wrong value cause' one is 12500 and the other is 65000.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#3

 I would wait a few months and go back and make an offer, the boobs pretty much blew their best chance of selling that cone speaker when they sold you the radio without it, it's unlikely that anyone would hand over $195 for something that is now basically useless for anything other than an ornament. Those speakers turn up with great regularity on fleabay for less then half that, to say nothing of swap meets.
Regards
Arran
#4

Arran, that's sorta my line of thinking as well. They also had a Radiola 18, asking price $95. It was missing the dial lamp hood, the back, and the dial would not turn. It had an Atwater Kent horn speaker with it, model M I believe. The radios and speakers were individually priced. They were asking quite a bit for it too. Do not remember exactly how much...but too much. I had taken a 9v battery with me to test any speakers I ran across. The horn was dead, the AK E series tested good. It was in as good of shape as the radio, so in a few months I'll go back and see if I can make a deal. If not, there are plenty of others as you said.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
My Philco 37-116 Restore
Measuring from center tap like the tube voltages show. Cap 127 is isolated from ground. Cap 127 shown in upper left of p...dconant — 08:05 AM
My Philco 37-116 Restore
Are you measuring relative to the centertap or the GND?morzh — 11:57 PM
Philco 610B oscillator wiring
Still not clear on the wiring interface between the 6A7 and oscillator. After refering to the available schematics and s...Tubester — 07:18 PM
Refinishing Ideas
My 37-116 code 121 is the best sounding radio i have...a daily driver. Since we are talking about "changes". ...poulsbobill — 07:18 PM
My Philco 37-116 Restore
Hello, I finally got brave enough to take the cans off the Expander Unit. Got the grid cap wires replaced and back toget...dconant — 06:50 PM
Zenith H725
I got into the first AM IF can today, and found its mica was cracked. Amazing that it was still working. This one makes ...EdHolland — 06:10 PM
Philco model #20
AHH HA , I got it and can’t thank you fellows enough , when I changed the capacitors I took the advice and did not unsol...onlyrick — 02:24 PM
Zenith H725
Hello Ed, yes, I like letting projects run for few days to make sure they don't start acting up . Sincerely Richardradiorich — 01:03 PM
Philco 46-480 Electronic Restoration
I am almost finished with this restoration. All which remains is the power transformer. I cleaned it up some time ago, b...jrblasde — 12:41 PM
Philco model #20
I seem to recall in some TRF sets there being a Local/Distance toggle switch that removes the B+ from the first 24 rf tu...RodB — 09:46 AM

[-]
Who's Online
There are currently no members online.

>