66B band switch question-SOLVED-
Posts: 825
Threads: 113
Joined: Aug 2012
City: The Villages
State, Province, Country: Florida
I don't know if anyone remembers, but a while back Morzh and I were trying to figure out the best way to free up the band switch. After a lot of work we were both able to get them freed up.
Now, my question: while I have the switch moving freely and switching properly, in my zeal to free it up I no longer have a stop. In other words, the switch now turns a full 360 degrees instead of stopping after one click to the right and one to the left.
Any ideas on what the stop is and what it looks like and where it is located?
Thanks,
Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org
Posts: 1,703
Threads: 55
Joined: Sep 2005
City: Evanston, IL
It should be right against the detent front plate.
The tab may be broken off and you can't recognize it?
Probably not an adjustable stop plate, but a tab preset.
Tab must be gone, if swx rotates 360.
Posts: 16,285
Threads: 567
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
Eric.....yeah, man, hate to break it to ya, but as Chick said (and you probably suspected it all along when you said something about "your zeal to free it up") you had likely broken some sort of a tab.
Which considering the degree of seizing (two hands effort and Robo-grip pliers produced little if any movement....what did they use for lube, Liquid Nails?) is something no one should be blamed for.
I do not remember how this thing looked exactly (I liked the idea of it coming out completely when the retention ring was removed...oh, wait....I did not have any retention ring  ) but if it had some sort of rib or a peg, you could (now that you can pull it out) in case of a peg drill a little hole (carefully not to break it) and glue in a cylindrical peg of some rigid insulating material, or if it is a a rib, simply glue a small bar of something along where the original was.
If you could produce a photo of what you have and point to the place of where the stop was we could brainstorm it here.
Of course it might be not on the rotor, but on the stator.....same thing, get a photo.
Posts: 825
Threads: 113
Joined: Aug 2012
City: The Villages
State, Province, Country: Florida
Yup. That's what I was afraid of. Now I just have to find out where it was and what it looked like.
Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org
Posts: 16,285
Threads: 567
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
Yep. Why don't you find out where it was and what it looked like. 
Suerte.
Posts: 825
Threads: 113
Joined: Aug 2012
City: The Villages
State, Province, Country: Florida
very funny
Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org
Posts: 825
Threads: 113
Joined: Aug 2012
City: The Villages
State, Province, Country: Florida
Well guys, thanks to you I figured it out. I pulled out the shaft and I could see where the stop was. I drilled a small hole in the Bakelite just below where the original was in the switch body. I super glued a small pin in the hole and...son of a gun! It works 
Thanks, guys.
Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org
Posts: 16,285
Threads: 567
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
An attempt to remove the Field Coil from a G speaker
|
| So,
Q1. Does anyone know where to get the spider.
Q2. If there is no such place, what material is best? I doubt tin is...morzh — 09:43 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| Arran
The oxidation seems to go deep, a few layers. The break starts right there, but then it will occur on every la...morzh — 07:35 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| Mike,
This is just a thought, the are on the coil where the verdigris (green oxidation is) I wonder if that is where ...Arran — 06:32 PM |
|
An attempt to remove the Field Coil from a G speaker
|
| Mike;
I've made a one or two spiders by using some card stock, and a razor blade, it took more then one try but they ...Arran — 05:48 PM |
|
Philco 91 Restore Code ??
|
| I wondered about that. Wish there was some place local to get this stuff.dconant — 04:20 PM |
|
Philco 89 indicator light.
|
| Bending the lamp bracket (moving the lamp, that is) can possibly change the shape of the pointer a bit, but not its loca...morzh — 04:01 PM |
|
Philco 91 Restore Code ??
|
| Because the usable power rating of it then is (3,200/20,000)*25W= 4W.
Maybe a tad more due to the mass, but not much. Yo...morzh — 03:59 PM |
|
Philco 89 indicator light.
|
| Thank you Dan, that was the trick. I kept trying to rebend the lamp bracket but that wasn't doing anything to help.Jim Dutridge — 02:18 PM |
|
Philco 91 Restore Code ??
|
| 20K 25 watt. I thought it was a 20 watt at first.dconant — 01:37 PM |
|
My Philco 37-116 Restore
|
| Nah, too much and not that important.morzh — 01:33 PM |
|
Who's Online
|
| There are currently no members online. |
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
