Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Atwater Kent 206
#1

Just need an opinion- to strip or leave it be. Stripping is not that difficult thing to do, just wonder if it still looks presentable.
Some like it that way, "patina" and all, not sure. Thanks.

[Image: http://i881.photobucket.com/albums/ac17/...172154.jpg]
#2

My opinion:

[Video: http://www.youtube.com/watch?v=Ho02oKHuveY]

--
Ron Ramirez
Ferdinand IN
#3

Only 1 picture, but, from that, I would 'let it be" too.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#4

I would also leave it as is. The finish is original only once, and for 80 years old it looks very nice. 
#5

I agree with everyone else..... leave it alone. The most I would do is a Go-Jo cleaning, some Howard's or Old English, and some quality paste wax.

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#6

It's a good looking cabinet. Paul said it best Icon_smile
#7

We have consensus by mavens..Needless to say, will comply.
Thanks guys.
#8

  I would have to see more pictures, with sharp focus, brighter lighting, and not at odd angles, sometimes they make things look better then they really are in person. A case in point was the Rogers Ten-60 I got from a guy selling it over craigslist, in a front on view it looked pretty nice, when I went to look at it in person I realized that someone had rubbed it down with Howard or some other scratch hiding product. Now obviously this set is not being pedaled on craigslist but a rub down with Gojo can have much the same effect, until the remnants of the Gojo evaporates.
Regards
Arran
#9

I wouldn't strip that. You can always touch the small worn areas up. If you use Howards you can touch up or go over it at any time with Laquer based products.
#10

(11-03-2014, 01:39 AM)Arran Wrote:    I would have to see more pictures, with sharp focus, brighter lighting,  remnants of the Gojo evaporates.
Regards
Arran

Your wish is my command.. Here it is, w/o GoJo:[Image: http://i881.photobucket.com/albums/ac17/...df5fda.jpg]
[Image: http://i881.photobucket.com/albums/ac17/...6fdca8.jpg]

[Image: http://i881.photobucket.com/albums/ac17/...9b882b.jpg]
Keeping the cabinet original, I did not want to have the chassis look brand new, just clean.
[Image: http://i881.photobucket.com/albums/ac17/...875acb.jpg]
[Image: http://i881.photobucket.com/albums/ac17/...ba0ff5.jpg]




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached.  I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM

[-]
Who's Online
There are currently no members online.

>