Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

New (to me) 57C
#1

Sorry, I am coming in late on this thread.  I have a Philco 57C that has been refurbished.  I am attempting to use it at my office.  Is it possible to use a home built antenna inside that will give me some reception?  I can pick up one station without too much effort (holding wire up to the 2 antenna connections).  I am very much a newby with these radios.

Thanks!

Rob
#2

locostbamboo
welcome to the phorum
guess it depends on what kind of office your in old building or new.  on how well it would work 
best to use long wire around or under carpet  with ground wire to water pipe or heater duct.
you can spend few bucks to get am transmitter and use that way you play any thing you like
sam
#3

Not exactly true, but close.  I bought the 57C at an auction years ago and my father knew someone who got it working for me.  It has a newer power cord and I believe had a tube or two replaced.  I am interested in any thoughts on an antenna.  I have it at work and my office is in the middle of a concrete building (old Best Buy).  I had a suggestion on an AM transmitter which sounds very promising.  I would appreciate any advice offered.

Thanks.

Rob in Oregon


Attached Files Image(s)
   
#4

Thank you Mafiamen.  I think the AM transmitter sounds really cool.  I did some research and it looks like I might be able to build one  (I am cheap)!  Icon_smile

I appreciate this and any other advice!

Rob
#5

moved post to keep in one place Icon_thumbup

hi rob
if going with am transmitter  one I use and most here I think use is
  sstran you build it your self comes as  kit but you need to know how to soldier as parts  are small
but worth it  about 100.
then you can use ipod or phone or computer to play what you like




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM

[-]
Who's Online
There are currently 4162 online users. [Complete List]
» 2 Member(s) | 4160 Guest(s)
AvatarAvatar

>