Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

My new A52CK
#1

Got this today finally! An A52CK Philco clock radio.

The guy said restored but geeze [Image: http://www.antiqueradios.com/forums/imag...lleyes.gif] 

Stripping it 98%, leaving spots of original lacquer on it and then painting brown paint with a small brush around the darker toned areas is not restoration........

Will have to redo in the spring. I still love it and thanks again Jim.  Icon_shh


Kirk


Attached Files Image(s)
       

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#2

Good looking radio Kirk. With your talent I'm sure it will be done right.
#3

Kirk;
  I knew what it would be like the first time you posted a link to that auction, a typical "antique mall" style restoration, or what I call a "strip n' clearcoat" job, there are a few of those sorts of radios on my nearby craigslist sites. If you know what to look for it's very difficult for them to hide, no toners, a flat lifeless look, pits from open grain.
Regards
Arran
#4

When I spotted the radio I reasoned ..not a horrible starting point...and a not so easy model to find.
Id rather find them absent toner than colored incorrectly so at least I can see the veneer I have to work with and in this case all the wood looks good and solid without any surprises as opposed to buried with toner or even worse...stained. Work some cabinet magic on this and it will be really pretty. I also like this version of the model better than the other
http://radioattic.com/item.htm?radio=0150114
#5

I just died!!!!!!

There are 2!!!! versions!!!!

Icon_e_surprised Icon_e_surprised Icon_e_surprised

Now I am back on the hunt  Icon_lolno  Icon_lol 

Thanks a lot Jim,  Icon_mrgreen

Kirk

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone,  As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM

[-]
Who's Online
There are currently 4810 online users. [Complete List]
» 3 Member(s) | 4807 Guest(s)
AvatarAvatarAvatar

>