1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
32-8274 trans
zfrederick
Junior Member
**
Posts: 16
Threads: 4
Joined: Nov 2014
City: VA
#1

11-28-2014, 02:23 PM
I'm in need of a replacement for the 32-8274 transformer but am having issues trying to find a replacement one. Can anyone point me in the right direction for a replacement. It has leaked out everywhere
Find
sam
Phorum Expert
*****
Posts: 2,572
Threads: 337
Joined: Jun 2013
City: lawrenceville nj
#2

11-29-2014, 02:43 PM
zfrederick
welcome to the phorum
sam
Find
morzh
Odobenus rosmarus
*****
Posts: 15,510
Threads: 544
Joined: Oct 2011
City: Jackson, NJ
#3

11-29-2014, 07:21 PM
Have you tried it though? It might've overheated but potentially still might work.
Try to run it UNLOADED for a few minutes, see what it consumes and whether it heats up.
Find
morzh
Odobenus rosmarus
*****
Posts: 15,510
Threads: 544
Joined: Oct 2011
City: Jackson, NJ
#4

11-29-2014, 09:58 PM
<P>Philco output transformer 32-8274: Primary impedance: 9000, Secondary impedance: 3.5. Power is not listed for this transformer, but similar physical sized ones are rated at 15 watts.


(from the other forum archives)

Which tells me 125 seies PP transformer (higher wattage model) will do.

125E.

Connect Voice coil to 2 and 4.

http://www.radiodaze.com/category/570.aspx
(This post was last modified: 11-29-2014, 10:01 PM by morzh.)
Find
Arran
Phorum Expert
*****
Posts: 4,655
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
#5

11-30-2014, 12:32 AM
 You could also try Edcore, they seem to have a good selection of tube type audio output transformers:

https://www.edcorusa.com/pushpull

Regards
Arran
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Jackson 665 j2 schematic request
FIXED!daveone23 — 03:55 PM
Bakelite crack repair - what is best epoxy?
Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM
Jackson 665 j2 schematic request
Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM
Jackson 665 j2 schematic request
Looking for a schematic for the 665 j2 multimeter.daveone23 — 04:42 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
>>I'll write to the Henry Ford. I heard, his secretary answers his mail, not he himself.morzh — 12:15 PM
Philco 48-200 alignment questions
Just checked the power cord and I did in fact wire it so the hot side (small prong) goes to the switch.transitony — 11:52 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
Thanks for the suggestions.  I'll write to the Henry Ford.   That would certainly make sense since by the time this prod...jeibner — 11:49 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
For what it's worth, the Henry Ford Museum and Greenfield Village in Dearborn, Michigan may be an option. The obvious ...GarySP — 11:39 AM
Help with Readrite 410 tube tester
Mike and I just had a short discussion yesterday about this very subject. So often it's the connections. Ya gotta have t...RodB — 10:08 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
We have a regional museum here in the Twin Cities called The Pavek Museum. They have an extensive collection of communic...RodB — 09:30 AM

[-]
Who's Online
There are currently 3042 online users. [Complete List]
» 1 Member(s) | 3041 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration