A cone crack - what is the best quick repair?
Posts: 1,703
Threads: 55
Joined: Sep 2005
City: Evanston, IL
Single layer of small strip(s) of tissue paper soaked in diluted Elmer's white glue (50:50) applied both sides, but just wide enough to bond the crack/tear without unduly stiffening a large area. Also, take a cotton swap in warm water to "pre-wet" the tear edges (both sides) for a better bond the to the dry cone.
Chuck
Posts: 15,810
Threads: 553
Joined: Oct 2011
City: Jackson, NJ
I bought contact cement today, did three layers on each side...will see how it behave.
Posts: 4,109
Threads: 310
Joined: Nov 2013
City: Kings Park NY
There is this great tutorial for speaker repair that someone posted but I cant remember the name........
Oh I know ... ME! 
That was before I knew about Syls tutorials.
http://philcoradio.com/phorum/showthread...l#pid64287
Kirk
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Posts: 2,128
Threads: 18
Joined: Oct 2008
City: Merrick, Long Island, NY
There is a glue for replacing speaker surrounds that is just right. For a small tear, artist's rubber cement is fine, although the days of paste up artists has passed, good luck getting it a reasonable pricel
Posts: 15,810
Threads: 553
Joined: Oct 2011
City: Jackson, NJ
Kirk
The problem is.....I drink ESPRESSO!!!!
Posts: 4,109
Threads: 310
Joined: Nov 2013
City: Kings Park NY
With beer?
Why am I even bothering to ask
Wait, beer before espresso makes quite the messo
Espresso before beer you're in the clear!
Just made that timeless quote up..
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
(This post was last modified: 12-19-2014, 04:29 PM by OldRestorer.)
Posts: 2,572
Threads: 337
Joined: Jun 2013
City: lawrenceville nj
think some one is still on happy pills
Posts: 15,810
Threads: 553
Joined: Oct 2011
City: Jackson, NJ
Exactly.
Happy pils. Which one is that, The Bud? (it is an unhappy pils for me, I prefer Czech)
(This post was last modified: 12-19-2014, 04:44 PM by morzh.)
Posts: 344
Threads: 38
Joined: Jun 2011
City: Tustin
State, Province, Country: California
I used service cement for years but the last couple years I have been using products made by Springfield speaker repair. A lot of guys that do Hi-Fi speaker repair use their CSA and rubber cements. I finally gave them a try and found that they work very well.
Posts: 4,109
Threads: 310
Joined: Nov 2013
City: Kings Park NY
You prefer Czech's,
I prefer ca$h.
But I'll take a Czech no matter how much it's written for! 
Kirk
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Posts: 15,810
Threads: 553
Joined: Oct 2011
City: Jackson, NJ
Note to self:
Check for a check for Czech beer. Check!
(This post was last modified: 12-25-2014, 12:17 PM by morzh.)
Posts: 371
Threads: 103
Joined: Jul 2011
City: Calgary, AB, CA
On any speaker repair that I have done ,I used'' Pliabond'' It is made by Goodyear and it never gets hard.
I am not sure where you can get it .. I get mine at Home Hardwar.
Users browsing this thread: 3 Guest(s)
|
|
Recent Posts
|
|
12' Philco
|
| If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel.
Kareem would have an e...morzh — 01:48 PM |
|
12' Philco
|
| And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM |
|
Hickok AC51 tube tester
|
| I think they have only shown the secondaries of the transformer.
Two of them feed the rectifiers' filaments.morzh — 12:58 PM |
|
IF can wire size and Rubber mounts?
|
| Arran
If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM |
|
12' Philco
|
| Rod,
Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently.
H...morzh — 12:54 PM |
|
Hickok AC51 tube tester
|
| Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM |
|
IF can wire size and Rubber mounts?
|
| Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM |
|
Hickok AC51 tube tester
|
| Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM |
|
IF can wire size and Rubber mounts?
|
| A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM |
|
My last cabinet for this year
|
| Hello Dan,
That is really beautiful what great looking radio you have !
I have friends who live in Calgary and the wea...radiorich — 01:51 AM |
|
Who's Online
|
| There are currently no members online. |
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
