Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Does anybody unkown philco?
#1

 I can not find this model in the gallery, maybe custom cabinet ?   Value as it sits ? no nobs , no tubes


Attached Files Image(s)
           
#2

The chassis is a 95.

The cabinet is a Philco Highboy:
http://www.philcoradio.com/gallery/1929c.htm#e

The grille insert is, most likely, not original. Notice how it is offset to the right and is also just a bit too wide (top to bottom) for the opening? I would bet it was installed later by someone who wanted something that looked a bit more decorative than the typical tapestry grille cloth, which may have become damaged prompting this addition.

--
Ron Ramirez
Ferdinand IN
#3

(01-12-2015, 09:43 PM)Ron Ramirez Wrote:  The chassis is a 95.

The cabinet is a Philco Highboy:
http://www.philcoradio.com/gallery/1929c.htm#e

The grille insert is, most likely, not original. Notice how it is offset to the right and is also just a bit too wide (top to bottom) for the opening? I would bet it was installed later by someone who wanted something that looked a bit more decorative than the typical tapestry grille cloth, which may have become damaged prompting this addition.
Nice detective work Ron, Was the wooden cross section on the legs offered to just some models? I checked on this one and no evidence any where ever on there  , was there  ever a speaker board for grill cloth to be attached? What would  this be worth as it sits?
#4

The legs on that cabinet were cut off just above where the stretcher base used to be. Compare your set to this photo:

[Image: http://www.philcoradio.com/gallery/images/1929/76h.jpg]

Look carefully at the legs, and compare to your radio. You will see what I mean.

I've never seen, or heard of, this model ever having a decorative grille - only the "Tapestry" grille cloth.

--
Ron Ramirez
Ferdinand IN
#5

You know your Philcos  Ron      . Case closed.  NEXT   Thank you
#6

 No knobs, no tubes, legs cut down, might be worth up to $30 as a parts set. Stuff like that is almost unsellable at the big swap meets, even in good condition and complete it's not a high dollar radio, most of those late 20s early 30s consoles are simply not.
Regards
Arran
#7

(01-13-2015, 01:03 AM)Arran Wrote:   No knobs, no tubes, legs cut down, might be worth up to $30 as a parts set. Stuff like that is almost unsellable at the big swap meets, even in good condition and complete it's not a high dollar radio, most of those late 20s early 30s consoles are simply not.

That being said, if you like it, give it the love.  If you're doubtful, you can always try a new idea that you're not sure you want to put on another cabinet.  However, I've seen your other cabinets... it's not like you need to practice.  I was kind of wondering if you'd contract out, actually.  Icon_wink Icon_lol
#8

Well, now that the question is on the console (thanks Arran!), Fred, do you contract out? Icon_wink   Joe

Joe

Matthew 16:26 "For what does it profit a man if he gain the whole world, yet lose his own soul?"
#9

(01-23-2015, 01:11 PM)DeckApe Wrote:  I've seen your other cabinets... it's not like you need to practice.  I was kind of wondering if you'd contract out, actually.  Icon_wink Icon_lol
 If you mean refinish restoration on the side , yes I do, check the Craig's list for dallas tx under antique radio you will see add. Send me a pm  I will give you my home phone  number
#10

(02-04-2015, 09:44 PM)Fred Taylor Wrote:  If you mean refinish restoration on the side , yes I do, check the Craig's list for dallas tx under antique radio you will see add. Send me a pm  I will give you my home phone  number

I'm good for now, but several others on here might be interested. You do phenomenal work!




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
I can't remember, but there was a particular product for loosening glue on the more modern "spiders", used pos...MrFixr55 — 09:43 PM
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM

[-]
Who's Online
There are currently 1911 online users. [Complete List]
» 2 Member(s) | 1909 Guest(s)
AvatarAvatar

>