Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Zenith Transoceanic battery-opinion
#1

Hi Guys,
I am finishing up my A600 Transoceanic and once it is finished it will be for sale. My question is whether I should go through the trouble to build a battery pack(these batteries are no longer available) or just sell it to run on A/C. The battery pack will cost me about $45.00 to construct plus the cost of 10 9 volt and 4 D cell batteries.
What do you think? Since it will not be an original battery, will it still be important to a buyer/collector?

Thanks,

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org

#2

eric
I don`t think it would be worth it to make battery
would increase 50. to 75. more for radio
as most don`t play them often or ones that do have batteries play very little from what I seen
sam

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
#3

 If your intent is just to fix this T.O up for resale I think that making a battery pack for it is a waste of time. I don't think it would add much, if any value, to a 600 series T.O, those seem to be among the most common tube T.O models you can find. Since these were all so called "three way" portables most people would just operate them from a line cord, if they wanted one that would be practical to run from batteries they can always pick up a later transistor model T.O. 
Regards
Arran
#4

Unless you want to sell the battery you make for a profit.
But: You cannot be sure that whosoever buys it will want the battery.
And: this whosoever can buy a battery from people who build and sell them should he ever want it.
#5

Icon_thumbup Thanks guys. I tend to agree with all of you.

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org





Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently no members online.

>