Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

philco 41-220 Questions
#1

Hey Guy's
I have a Philco 41-220 that I'm having a problem with the alignment. 
Here is the link   http://www.nostalgiaair.org/PagesByModel...013395.pdf
Here is a some info I came across which pretty accurately describes what I'm hearing
http://www.antiqueradios.com/forums/view...6&t=213839 

I have tested the tubes the only problem is the 35A5 is replaced with a 50A5 could this be a problem?

Is there a way to find if there was a change in this radio concerning the IF can's? I ask that in #26 the 2nd IF should only have one trimmer and I have two? I also checked the Resistance of the coils and they are 25 & 26 ohms and the print shows 60 & 8 ohms??

When doing step one where it calls for hooking the signal gen "ant section of tuning section" are they referring to 5B?

Should I put a .05 cap in series with the signal lead? Should I disconnect the external antenna in this first step? I don't seem to pickup a tone at 455.
the other steps I get a tone at 1600 and 1500.

Thanks Eric
#2

I figured out what I did wrong! #9 a .25 cap also had a wire wrapped around one end and electrical tied to that end and then to ground. and that end of the cap went to the center of the 7c7 which when I checked was not grounded even though it looked like it was so I added that wire to ground and that took care of it!

Eric
#3

Icon_thumbup




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Model 96 cabinet veneer
There is some description of the veneers in the 1930 Brochure in our library. Here's the link: klondike98 — 11:59 PM
Philco 91 Speaker Replacement
I can't remember, but there was a particular product for loosening glue on the more modern "spiders", used pos...MrFixr55 — 09:43 PM
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM

[-]
Who's Online
There are currently 1098 online users. [Complete List]
» 2 Member(s) | 1096 Guest(s)
AvatarAvatar

>