Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Using Gojo Creme on veneer
#1

I watched a guy on YT do this to his rather nasty looking Philco, and I was amazed with the results! The Gojo Creme is about $2.00 for a good sized jar at your local auto parts store. It cleans the veneer right up! I highly recommend it. Just get a soft cloth and a small helping of the stuff and gently rub it with the grain on your Philco's veneer.


Attached Files Image(s)
   

Slave to an RCA Victor CTC-25
#2

which auto parts store?
#3

Non pumice right?
Works great!

Kirk

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#4

I got it at O'Reilly. They have pumice, but I did not want to use that in case it would scratch.

Slave to an RCA Victor CTC-25
#5

I just did this with my 40-180. I don't have a before picture but this is the after. I love it and would recommend it to anybody. Works GREAT!


Attached Files Image(s)
   
#6

"Washing" a cabinet with go-jo is a great way to remove the years of attic dirt. It gives you a better idea just what condition your cabinet is in and whether or not you want to refinish. 

I have had many cabinets that literally "came alive" after being cleaned with go-jo. 

NEVER use the go-jo with pumice on a cabinet!!
#7

I also use the go-jo first on any cabinet I get that looks promising, no wood damage that needs repair etc.. Have had good luck with it.
#8

I"ve used it on grimey chasses as well.
#9

Found some at a NAPA store.
#10

I found it at Wallmart in the automotive department. [[hand cleaner]

   Living in Calgary Alberta
#11

Is GOOP the same stuff? Looks the same and smells the same. Its gojos competitor, I found Goop at Walmart, they didn't have gojo. I use it for my hands. Haven't tried yet on wood cabinets.
#12

Yes  goop is same thing as gojo

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
#13

I'm assuming that these success stories are on cabinets that were pretty much perfect and just had years of grime build up.

My first to radios were a disaster and Gojo would have done nothing.
#14

(07-12-2015, 11:42 PM)Edisla Wrote:  I'm assuming that these success stories are on cabinets that were pretty much perfect and just had years of grime build up.

My first to radios were a disaster and Gojo would have done nothing.

Yes its just for dirt, wax build up? , grime , grudge, grease, grit, finger prints, oil, latex paint, crayons, ink, ant piss, dust, lite water marks, bullet holes, cigar burns, cigarette burns, dryed whiskey, spilt soda, beer, tea, coffee, also repels spiders , roaches, piss ants, silverfish , etc. Icon_wave Icon_wave Icon_wave Icon_wave Just messen around Edisla Icon_crazy Icon_crazy Icon_crazy Icon_crazy Icon_crazy Icon_crazy Icon_crazy
#15

I use Non pumice Goop and 0000 steel wool.  I just cleaned up a 46-1203 last night and it came out looking great!  In fact I think I'll change my avatar from the refinished 48-1256 to the original finish 46-1203!




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic.  This radio had a 8" Zenith  speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM

[-]
Who's Online
There are currently 4448 online users. [Complete List]
» 3 Member(s) | 4445 Guest(s)
AvatarAvatarAvatar

>