Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

re-calibrate hickok 800
#1

Hi Guy's,
Anyone know what it costs to have a Hickok 800 calibrated?
Thanks,
murf
#2

Was hoping someone who had done it would answer but I seem to recall reading someone who offered cal in the $150 range but don't think that included shipping. Cannot seem to find that reference now though.
#3

If you have the test equipment recommend Alan Douglas' book, it has good information in it about the calibration of almost any Hickok tester. Most of them employed the same circuit and associated voltages. 

If not:  http://www.alltubetesters.com/

Or:       http://www.radiolaguy.com/info/tubeTesterRest.htm
#4

Would strongly that you get the procedure and do it yourself. You will gain a much better understanding of what your tester is doing and how it is being done AND possibly what to look for in respect to tubes that tube testers do not test very well. Schematic for 800A here:

http://bama.edebris.com/manuals/hickok/800a/

But you will need to search for alignment instructions as well.

MOST important to note that the alignment(s) were written for people using 10,000 ohms/volt meters ( you will need to use resistors if using a digital VOM).

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#5

The ohms per volts is usually included in the calibration instructions. As a rule, the earlier the instrument or radio you are working on, the lower (and hence more "loading" of the item you are measuring) the ohms per volt rating specified for the VM required. 

Since we are on the subject, I would like to recommend to all of you an instrument that a good bud gave me a year ago. It is a military AN/USM 223 Multimeter. One of the neat features it offers is the option of 1000 ohms per volt OR 20 thousand ohms per volt for DC measurements.   
#6

(06-29-2015, 10:37 AM)TA Forbes Wrote:  The ohms per volts is usually included in the calibration instructions. As a rule, the earlier the instrument or radio you are working on, the lower (and hence more "loading" of the item you are measuring) the ohms per volt rating specified for the VM required. 

Since we are on the subject, I would like to recommend to all of you an instrument that a good bud gave me a year ago. It is a military AN/USM 223 Multimeter. One of the neat features it offers is the option of 1000 ohms per volt OR 20 thousand ohms per volt for DC measurements.   






Yep.

I have 2 or 3 nice VTVMs. I think the last one I was using was not isolated from the line. Dumb. Don't remember the ohms/volt on it.

Really the best for caling the old tube testers would be the 80s model Archer (radio shack) I keep at home to check such thing as AA batteries, replaced at the shop with the big $$ Fluke.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 3743 online users. [Complete List]
» 1 Member(s) | 3742 Guest(s)
Avatar

>