Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

RCA 8t plays again/REDO DIAL
#1

RCA 8t was on my list to restore so over the coarse of a week I managed to complete this radio although after playing for a while I think I need to rebuild the volume  control or replace it , but other than that I think it turned out nice, I like to find a 10t which I think is the grand Daddy of these model cabinets line up. Payed 75$ for this one off Craig's list, cleaned up pretty nice.


Attached Files Image(s)
                   
#2

Before pictures of RCA 8T


Attached Files Image(s)
                   
#3

Beautiful Fred. Very nice work indeed.

Crist
#4

(07-05-2015, 09:45 AM)Fred Taylor Wrote:  RCA 8t was on my list to restore so over the coarse of a week I managed to complete this radio although after playing for a while I think I need to rebuild the volume  control or replace it , but other than that I think it turned out nice, I like to find a 10t which I think is the grand Daddy of these model cabinets line up. Payed 75$ for this one off Craig's list, cleaned up pretty nice.

Forgot inside pics


Attached Files Image(s)
       
#5

Your usual great job Fred. VERY nice.
Jerry

A friend in need is a pest!  Bill Slee ca 1970.
#6

That's a beautiful job. I have a question about the dial bezel: Would it be a bright brass like that originally? Most of the 30's radios I have are dark brass now, almost black, but then they're about 80 years old. How did they start life? One of my Z tombstones appears in a couple of 30's movies, including a Bob Hope movie. I always forget to note if the bezel is shiny or dark in that 1941 movie. Again, that's a really nice radio!
#7

I don't like it  polished up like that, I was told that this model RCA was highly polished, is how they were when new. Im going research it more and may change it if need be.
#8

One of the first radios I ever owned, about 100 years ago, was an RCA 5T1 -a smaller version of this set. To this day I am still amazed at how sensitive that five-tube tombstone was. I can only imagine what an 8-toober must be like.

As to whether the escutcheon was shiny or not - ask Doug Houston, he would probably know.

--
Ron Ramirez
Ferdinand IN
#9

I would shoot the bezel with a light coat of Van dyke Brown toner. Take some of the glow off.

"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
#10

 I believe that this chassis is shared with the 8K and with the Canadian G.E E-8/E-86, as well as the 7T and 7K which are the same except for the lack of a Magic Eye tube. One thing I can see straight away is that the chassis is missing the two filter capacitor cans, one was mounted on the right from corner, the other on the left rear corner. Also the IF can towards the left front of the chassis is a replacement, the original looked like the one closer towards the left rear with a pair of tunable slugs, top and bottom, rather then trimmer caps in the top as the replacement has. The speaker and it's cable are also replacements, RCA did not use Utah speakers, and their speakers also had a four pin Bakelite plug mounted to the rear with a matching socket on the end of the speaker cable like a 1940s Philco would have.
Regards
Arran
#11

Fred, I have one of these sets and they work great! Also have a RCA 5U it has a turn table on the top but that does not work. But the radio works fine. The 8 tuber is a lot better.
#12

Arran,

judging by everything being this dirty and rusty, the replacement (if it is) is more or less contemporary or in any case quite old and from the era when people still used and repaired these radios which I think could be 40-s to 50-s. For me it is all old and acceptable, unless you are Russ and doing trye to factory restoration for a museum Icon_lol

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#13

I went ahead and darkened the escution, looks better Icon_eek and the eye tube trim ring Icon_eek and replaced some more caps Icon_eek,plays better and sounds better, no more feed back at low volume Icon_eek  


Attached Files Image(s)
               
#14

(07-07-2015, 09:45 AM)morzh Wrote:  Arran,

judging by everything being this dirty and rusty, the replacement (if it is) is more or less contemporary or in any case quite old and from the era when people still used and repaired these radios which I think could be 40-s to 50-s. For me it is all old and acceptable, unless you are Russ and doing trye to factory restoration for a museum Icon_lol

Mike;
  RCA slug tuned IF cans were 455KC, were used for a number of years, and are quite easy to find. Besides it looks out of place being shorter and of a completely different design, it is a restoration after all, not a repair.
Regards
Arran
#15

I think it looks better now that you have changed the color of the escutcheon. It looks more original.
Nice job on the cabinet

   Living in Calgary Alberta




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM
Made mistake & did not label connection
You'll have to forgive me, I am not sure what you mean.  Can you explain what you are really saying.  If anyone does not...georgetownjohn — 08:05 PM
Made mistake & did not label connection
Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM
Made mistake & did not label connection
Maybe this is starting to make some sense in my hard head.  Is this why the wire in question was not in the great Ron Ra...georgetownjohn — 04:34 PM
Made mistake & did not label connection
I was correct with the 6A8 pin connection's, 7 and 8 are connected to ground as well as the tube shield (the broken line...RodB — 02:41 PM
Made mistake & did not label connection
What does the dotted line representing that surrounds the tube in the schematic?georgetownjohn — 02:17 PM
Made mistake & did not label connection
Hello John, I have been there either label got lost or was not labeled ! Sincerely Richardradiorich — 02:15 PM
Made mistake & did not label connection
Sorry, it is a Philco 37-640.  Does that help?--Johngeorgetownjohn — 02:14 PM

[-]
Who's Online
There are currently no members online.

>