Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
As we discussed on another thread, I just picked up a 40-170 Chairside. I've checked all my resources, but can't seem to find any information on it, other than the one sold in 2011 on Radio Attic, and an approx. value in the Collector's Guide, and, of course, schematics on Nostalgia Air. Does anyone know how many of these were made? Or their popularity?
This also has castors instead of metal feet. It looks like they are original. Anyone know anything about these?
Pat
Posts: 142
Threads: 15
Joined: Nov 2008
City: Glenshaw, PA
Oh! Pictures Please! We are all dying to see a 40-170CS.
Posts: 5,088
Threads: 270
Joined: Nov 2012
City: Wilsonville
State, Province, Country: OR
Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
I'll take a post some pics today as I start disassembly. You will notice that the top 2 inlays are bird's eye maple, which was installed by the OP. I'll be replacing these with book match burl, either mahogany or walnut.
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
*Important Reminder: remember, this site is the place for all things Philco. MANY questions about anything Philco are answered simply by looking here.
That is a sharp looking set! I have never seen one other than photos.
Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
Posts: 5,088
Threads: 270
Joined: Nov 2012
City: Wilsonville
State, Province, Country: OR
Looks to be in great shape!! Nice find
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
You won't be doing a lot of SW DXing, but that is one swell set!!! 
Posts: 10
Threads: 2
Joined: Jun 2015
City: Portland,Oregon
I know that I'm just getting started here, but that the exact model I hope to find.
I remember sitting in Grandpas lap as he tuned a radio back in the early 50's ...never knew the radio but remember the experience.
Lee
(This post was last modified: 07-23-2015, 08:41 PM by NN7X.)
Posts: 4,707
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
(07-23-2015, 08:21 AM)Patrick Wrote: I'll take a post some pics today as I start disassembly. You will notice that the top 2 inlays are bird's eye maple, which was installed by the OP. I'll be replacing these with book match burl, either mahogany or walnut.
I would leave the birdseye in there, believe it or not Philco did make some cabinets using figured maple. I can't say that this was factory built but if it was not it was very professionally done if it wasn't.
Regards
Arran
Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
(07-24-2015, 06:44 AM)Arran Wrote: (07-23-2015, 08:21 AM)Patrick Wrote: I'll take a post some pics today as I start disassembly. You will notice that the top 2 inlays are bird's eye maple, which was installed by the OP. I'll be replacing these with book match burl, either mahogany or walnut.
I would leave the birdseye in there, believe it or not Philco did make some cabinets using figured maple. I can't say that this was factory built but if it was not it was very professionally done if it wasn't.
Regards
Arran I've already removed the bird's eye. The PO said he installed it, and upon closer observation, you could see where he had to fill in the edges with putty. I'm not a purist, but I am somewhat of a perfectionist, and his imperfections were quite obvious.
Users browsing this thread: 2 Guest(s)
|
|
Recent Posts
|
|
Philco 60 Squealing
|
| Well, a wave trap is a trimmer in series with the coil so at the resonant frequency it provides a short to ground. This ...RodB — 10:07 AM |
|
Philco 60 Squealing
|
| Rod, My radio is run 7. The wave trap is on that schematic as shown in the picture.
dconant — 09:21 AM |
|
American Bosch Model 802 auto radio
|
| Hi Arran ,
Thanks for your help with this radio.And especial thanks for letting me know to look it up under United Ame...Antipodal — 04:32 AM |
|
Philco 60 Squealing
|
| Usually a wave trap is for keeping IF signals from entering the antenna and from leaving the antenna. You feed an IF sig...RodB — 09:30 PM |
|
Philco 60 Squealing
|
|
I just peaked it for the best signal at 600.
NULL it for IF frequency, originally it would have been null for 500kh...Chas — 08:05 PM |
|
Philco 60 Squealing
|
| Wavetrap no longer matters.morzh — 05:19 PM |
|
Philco 60 Squealing
|
| Rod, I had checked out your suggestions but did not help. I did solder the ground rivets to the chassis as Chas suggeste...dconant — 04:52 PM |
|
37-690 Bass Choke Replacement
|
| Yeah, I know, Mouser and Digikey don't have "big iron" components. For some reason Philco was messing with the...Radiodial — 04:25 PM |
|
37-690 Bass Choke Replacement
|
| Yes, I just had to deal with that while repairing the 37-604 Philco. Exactly that value choke was gone. And the current ...morzh — 03:52 PM |
|
37-690 Bass Choke Replacement
|
| Ah, now where to find one.
I've into this before on smaller sets, I now recall. Hammond makes one that is only rated...Radiodial — 03:27 PM |
|
Who's Online
|
There are currently 5353 online users. [Complete List]
» 3 Member(s) | 5350 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
