Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

38-116 off Craigslist
#16

[Image: http://i1319.photobucket.com/albums/t679...y9a9al.jpg]


[Image: http://i1319.photobucket.com/albums/t679...w9hvrg.jpg]

Nearly done with the cabinet. Few more details to finish up. Grill cloth on the two smaller speaker outlets nearly drove over the edge. Looks slightly different depending the angle you see it from. Finally chose one set up, and left it. Waiting on the capacitors to be delivered so I can start on the re-cap. 
#17

Very nice looking. Great job. Good luck with the chassis restore.
#18

Did the 38-116 have a back cover?? I know that some of the older higher end sets had a cover over the spkr section for acoustic. Even with some vent hole at the top for the electronics would think it would get hot in there.

Terry
#19

Just wanted to add, finished the re-cap and it's playing great. I see what all the hype is about. This thing sounds great and the volume, without distortion, is incredible. A new favorite. 
#20

Nice job refinishing the cabinet. We all knew you had it in you! Looks great!
#21

Looks fantastic!

 I just got one and the ONLY good thing about it, is that the finish is already 99% stripped.

Me


Attached Files Image(s)
   

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#22

Kirk where did you find yours?
#23

I got them from Oyster bay Long Island


Kirk

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#24

Kirk,
 Them? How many did you get?
                            Henry




Users browsing this thread: 6 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently no members online.

>