Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Croydon/Halson recap
#16

Gotten lit lately??? Heaters I mean.

Terry
#17

I think the person who was supposed to send them forgot or finked out Icon_sad
Maybe they will come today?
Yes I got lit last night...
Me!

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#18

are these the correct ones?
Sal has them and I am ordering today.

New lower prices on diodes

1N4007 1000 volt 1 amp diodes
10 for $0.50.....25 for $1.00.....100 for $3.50

UF4007 1000 volt 1 amp Fast Recovery Diodes
10 for $1.00....25 for $2.00.....100 for $6.00

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#19

(10-12-2015, 11:39 AM)OldRestorer Wrote:  are these the correct ones?
Sal has them and I am ordering today.

New lower prices on diodes

1N4007 1000 volt 1 amp diodes
10 for $0.50.....25 for $1.00.....100 for $3.50

UF4007 1000 volt 1 amp Fast Recovery Diodes
10 for $1.00....25 for $2.00.....100 for $6.00
Yep the 1N4007 are fine. Go a head and splurge buy 10. They do come in handy. What we are look to do it rectify 120v at .3 of an amp
Terry
#20

PM me your address and I'll pop a few 1N4007's in the mail for you tomorrow, unless you have other stuff to order from Sal.

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#21

Thank you much John,
I did have an order for Sal.
Me

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6




Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I'm pretty sure I now have the litz wire soldered. This did not make any difference. Back in April I rewound the seconda...dconant — 06:25 PM
Philco 38-7 Speaker
Just to make sure, you chose either 4 ohm into 5K or into 10K? (blk-org or blk-grn)morzh — 06:23 PM
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM

[-]
Who's Online
There are currently 4665 online users. [Complete List]
» 4 Member(s) | 4661 Guest(s)
AvatarAvatarAvatarAvatar

>