Posts: 330
Threads: 40
Joined: May 2015
City: Sanger, CA
State, Province, Country: California
Does anyone make the correct speaker cloth for this cathedral? The label only says Model 60, not 60B, etc...
The one I'm contemplating buying has nice cloth, but has a pinkie finger sized stretched dimple in the cloth, supposedly, not a hole. I may need to replace the cloth or attempt to moisten that spot and shrink it with a hair dryer, if that's possible.
Any thoughts?
Posts: 5,090
Threads: 270
Joined: Nov 2012
City: Wilsonville
State, Province, Country: OR
Which 60 are you planning on buying? See Ron's page of versions of cabinets: http://www.philcoradio.com/tech/60evol.htm
I know the 60MB is not reproduced but I did find a cloth online that was pretty close.
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
(10-27-2015, 11:08 PM)klondike98 Wrote: I know the 60MB is not reproduced but I did find a cloth online that was pretty close.
Where did you find it, Bob? I have a 60MB that will be needing some cloth...
--
Ron Ramirez
Ferdinand IN
Posts: 330
Threads: 40
Joined: May 2015
City: Sanger, CA
State, Province, Country: California
Bob,
It's the one on the right side marked July '34 or the one on the left, second row marked June'35. That's the style cloth.
Steve
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
SteveG
You want GRC05 from Radio Daze.
http://www.radiodaze.com/grille-cloth-05-item-grc05/
Incidentally, the greenish lines should be vertical, not horizontal as shown in the Radio Daze photo.
--
Ron Ramirez
Ferdinand IN
Posts: 5,090
Threads: 270
Joined: Nov 2012
City: Wilsonville
State, Province, Country: OR
Posts: 330
Threads: 40
Joined: May 2015
City: Sanger, CA
State, Province, Country: California
Thanks Ron. Now to get that radio home. Anyone have thoughts about shrinking the stretched spot before I have to consider replacing the grille cloth??
Posts: 4,109
Threads: 310
Joined: Nov 2013
City: Kings Park NY
Hey,
How big is the indent and how deep?
Shrinking the fabric is doubtful but you may be able to press it flat and iron it between 2 towels or pieces of fabric.
Just be cautious that the old glue may stick to the piece it is attached to so be careful.
Me
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
Thank you, Bob, for the info. 
--
Ron Ramirez
Ferdinand IN
Posts: 330
Threads: 40
Joined: May 2015
City: Sanger, CA
State, Province, Country: California
Kirk,
It looks like it's about 1/2"-3/4" in diameter and maybe 3/8" deep. I think between two moist towels with the iron might be the trick. Steaming is how they tighten seat material at the upholstery shop my friends run... I was worried that if I sprayed liquid on the cloth and then used the hair dryer, it would release 80 years of soiling from the cloth and stain it. I added a picture of the radio. Not the clearest, but it's the best I have right now.
Steve
[Image: http://www.surfacezero.com/g503/data/500...280369.JPG]
(This post was last modified: 10-28-2015, 11:30 AM by SteveG.)
Posts: 5,090
Threads: 270
Joined: Nov 2012
City: Wilsonville
State, Province, Country: OR
Hey Ron, I was able to track down the order I made for the 60MB grille cloth and it was from the same vendor but may be a slightly different cloth than what I posted above. See:
http://www.ebay.com/itm/ANTIQUE-RADIO-GR...5b1b358b18
This one looks a little different in his photos ... hard to tell by viewing on line but I think this one looks more like the original cloth than what I posted earlier. Anyway...the above (or the 12 x18 version of it) was what I bought. Sorry for any confusion.
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
American Bosch Model 802 auto radio
|
| Hello again;
I found a model 838 car radio on Nostalgia Air under United American Bosch, http://www.nostalgiaair.org/...Arran — 09:32 PM |
|
New Philco Repair Bench
|
| Morzh is correct. The repair bench on our website is an archived image of chuck’s original site. He no longer provides s...klondike98 — 05:32 PM |
|
Made mistake & did not label connection
|
| Excellent information. It is all starting to come together now and your explanation really helped since I noticed that ...georgetownjohn — 04:39 PM |
|
Made mistake & did not label connection
|
| Hi John,
I don't have this radio, but I can supply some info:
Based on your pic, pins 7,8 and 1 are used together, go...MrFixr55 — 02:02 PM |
|
New Philco Repair Bench
|
| As far as I know, the Repairbench does not work, and has not been working in a while.
Chuck (we had that campaign looki...morzh — 01:33 PM |
|
Radio city products 664 schematic request
|
| Need a schematic or manual for the 664. The 663 may be similar.daveone23 — 12:38 PM |
|
New Philco Repair Bench
|
| Thanks Gary.dconant — 12:16 PM |
|
New Philco Repair Bench
|
| I tried accessing the site through our library and got the same response. It's reported to our tech gurus. GaryGarySP — 11:50 AM |
|
New Philco Repair Bench
|
| I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM |
|
Made mistake & did not label connection
|
| It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires.
Why'n't you...morzh — 09:49 PM |
|
Who's Online
|
There are currently 4039 online users. [Complete List]
» 1 Member(s) | 4038 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
