Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Phlaky Lacquer
#1

I'm starting work on the finish of 2 cabinets. One is a Philco 650 and the other is a 1940 Farnsworth. The finish on the Farnsworth has flaked off slightly in some spots and heavily in others (see pics). I have been reading this forum and have not yet run across a discussion on how to proceed in either case. Will I have to strip the finish or is there a way to repair?  The 650 has a few areas near the bottom that are slightly flaked off.

Rod
#2

I cant tell if that is photofinish...

If it isnt then you will have to strip it. No way to match the toner and the flaking is too unstable.
If it is photofinish you can recreate it on a computer or if you have artistic talents then you can do it with paints.

I completely redid the photofinish on a philco radio clock lamp and it was not that hard.

First we need to know what the finish is.

Kirk

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#3

Kirk - Sorry about the phuzzy photo. It's veneer with toned lacquer. The 2 inch wide horizontal piece at the bottom of the pic halfway down the cabinet might be photo finish and I probably won't have to do anything with that. So you're saying I should strip the badly flaked off area? What about the occasional single tiny area?




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM
Philco 60 Squealing
I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM
Philco 6K7
I am restoring a Philco 37-60. The am reception is very good, but the shortwave is very weak. Run 6 Philco removes the g...bobbyd1200 — 01:35 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A5...MrFixr55 — 06:48 AM
American Bosch Model 802 auto radio
I think it would come under either American Bosch or United American Bosch. American Bosch made sets for the American We...Arran — 05:53 AM
trying to identify this wire type
Thanks to all for the feedback. As Arran said, it is probably an older replacement and yes it has a grid cap so I will ...georgetownjohn — 09:32 PM
trying to identify this wire type
It's possible that the red wire, actually a grid cap lead, is a very old replacement, I can't remember seeing a pre 1939...Arran — 09:18 PM

[-]
Who's Online
There are currently 4465 online users. [Complete List]
» 1 Member(s) | 4464 Guest(s)
Avatar

>