Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

custom zenith console project (FINISHED!)
#22

Well this is it, one of a kind. Completely not done but very close , will have to do some cabinet touch up and maybe change grill cloth out to something else don't know yet on that. There is a little compound in a few crevices that needs to be taken care of and needs to be waxed after a few weeks , have to let the lacquer cure out before I do any waxing and being careful not to get into any crevices, its very hard to get out once in there. The sound of this set is amazing , sure am glad I did it because it looks wonderful and only one in the world that I know of, like this. No shabby chick or butcher job on this one folks. High quality at its best on this antique radio, so so smooth its like glass just like a high dollar piano, my car refinishing skills really paid off on this one .Thanks for looking and I will start another radio project soon maybe the 37-650px Icon_eek Icon_eek Icon_eek Icon_eek Icon_eek Icon_eek Icon_eek


Attached Files Image(s)
                   


Messages In This Thread
RE: custom zenith console project - by sam - 11-17-2015, 10:57 PM
RE: custom zenith console project - by Arran - 11-17-2015, 11:33 PM
RE: custom zenith console project - by Arran - 11-18-2015, 01:53 AM
RE: custom zenith console project - by morzh - 11-18-2015, 12:05 AM
RE: custom zenith console project - by sam - 11-18-2015, 01:12 PM
RE: custom zenith console project - by JimZ - 11-29-2015, 09:06 AM
RE: custom zenith console project - by JimZ - 11-29-2015, 10:09 AM
RE: custom zenith console project (FINISHED!) - by Fred Taylor - 11-30-2015, 10:21 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 5736 online users. [Complete List]
» 1 Member(s) | 5735 Guest(s)
Avatar

>