1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
38-690 volume control
etech
Member
***
Posts: 237
Threads: 24
Joined: Dec 2007
City: Gladwin, MI
#7

12-09-2015, 11:25 AM
(12-09-2015, 10:20 AM)Chuck Schwark Wrote:  Ah, ok.  My Philco original schematics do NOT show any parts values.  ??

Could be a very early edition maybe.  Will have to research.....

Thanks,

Chuck

Hi Chuck,

I took the information from the schematic you sent me as part of my packet. It is marked "38-690 Code 125 Figure 1". On the back side of this page is the alignment page and the chassis pictorial page.

Best regards,

Ed
Find
« Next Oldest | Next Newest »


Messages In This Thread
38-690 volume control - by FStephenMasek - 12-07-2015, 03:11 PM
RE: 38-690 volume control - by Chuck Schwark - 12-07-2015, 03:40 PM
RE: 38-690 volume control - by Chuck Schwark - 12-09-2015, 10:22 AM
RE: 38-690 volume control - by SteveJB - 12-18-2017, 08:42 AM
RE: 38-690 volume control - by morzh - 12-18-2017, 09:21 AM
RE: Resistance values for 38-690 vol pot - by etech - 12-09-2015, 11:25 AM
RE: Resistance values for 38-690 vol pot - by sam - 12-09-2015, 11:50 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
trying to identify this wire type
Thanks to all for the feedback. As Arran said, it is probably an older replacement and yes it has a grid cap so I will ...georgetownjohn — 09:32 PM
trying to identify this wire type
It's possible that the red wire, actually a grid cap lead, is a very old replacement, I can't remember seeing a pre 1939...Arran — 09:18 PM
Gilfillan Brothers Car Radio?
Hi everyone,  Special thanks to Joe Rossi for tracking down this obscure radio and thanks to others who took up the hun...Antipodal — 08:15 PM
trying to identify this wire type
Here's one source for your wire of many. Take care and BE HEALTHY! Gary P.S. Can't get the right color you need? I ...GarySP — 06:40 PM
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached.  I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration