1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
41-285 Don't Know What To Do Next
Johnny
Junior Member
**
Posts: 22
Threads: 8
Joined: Apr 2009
#9

04-17-2009, 09:21 PM
Hello again,

So I cleaned those pesky loctals again but to no avail. The same problem still exists. The pins and the sockets for the loctals are very, very clean. I really need to know how to induce the signal into the individual stages to test the IF circuits. I have the heath IG-102S generator but I don't see a signal on the jack that is supposed to be the "modulated" RF output. I do have 455khz from the "RF" output jack. I really need this procedure explained to me or reference a web site that does so.

Thanks much,

Johnny
Find
« Next Oldest | Next Newest »


Messages In This Thread
41-285 Don't Know What To Do Next - by Johnny - 04-16-2009, 10:07 PM
Re: 41-285 Don't Know What To Do Next - by Johnny - 04-16-2009, 11:27 PM
Re: 41-285 Don't Know What To Do Next - by Johnny - 04-17-2009, 01:47 AM
Re: 41-285 Don't Know What To Do Next - by Johnny - 04-17-2009, 03:41 PM
Re: 41-285 Don't Know What To Do Next - by Johnny - 04-17-2009, 06:09 PM
Re: 41-285 Don't Know What To Do Next - by Johnny - 04-17-2009, 09:21 PM
Re: 41-285 Don't Know What To Do Next - by Johnny - 04-19-2009, 07:56 PM
Re: 41-285 Don't Know What To Do Next - by Johnny - 04-20-2009, 10:54 AM
Re: 41-285 Don't Know What To Do Next - by Johnny - 04-20-2009, 02:35 PM
Re: 41-285 Don't Know What To Do Next - by Johnny - 04-20-2009, 06:45 PM
Re: 41-285 Don't Know What To Do Next - by Johnny - 04-21-2009, 01:20 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Bakelite crack repair - what is best epoxy?
Thanks everyone. I appreciate you sharing your experience and looks like I'll work with the 24 hr two part clear epoxy....de371 — 10:25 PM
Jackson 665 j2 schematic request
Without a schematic its going to be hard tracing the wire wound spool resistors.daveone23 — 05:21 PM
Jackson 665 j2 schematic request
Looking for a schematic for the 665 j2 multimeter.daveone23 — 04:42 PM
Looking for place to donate unique Philco Philco J-1930 Prototype
>>I'll write to the Henry Ford. I heard, his secretary answers his mail, not he himself.morzh — 12:15 PM
Philco 48-200 alignment questions
Just checked the power cord and I did in fact wire it so the hot side (small prong) goes to the switch.transitony — 11:52 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
Thanks for the suggestions.  I'll write to the Henry Ford.   That would certainly make sense since by the time this prod...jeibner — 11:49 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
For what it's worth, the Henry Ford Museum and Greenfield Village in Dearborn, Michigan may be an option. The obvious ...GarySP — 11:39 AM
Help with Readrite 410 tube tester
Mike and I just had a short discussion yesterday about this very subject. So often it's the connections. Ya gotta have t...RodB — 10:08 AM
Looking for place to donate unique Philco Philco J-1930 Prototype
We have a regional museum here in the Twin Cities called The Pavek Museum. They have an extensive collection of communic...RodB — 09:30 AM
Philco 89B code 123 newbie
I did some nosing around and found that the original caps were 4 3/4" long x 1 5/16" in dia. Guess what 1"...Radioroslyn — 09:28 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration