Zenith 6-D-2615 project

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Zenith 6-D-2615 project

Paul Philco322
Super Moderator

Posts: 4,381
Threads: 412
Joined: Jun 2011
City: Boston State, Province, Country: Massachusetts

01-02-2016, 10:33 PM

It will be a fine sounding set when done. I would remove the asbestos, save someone else the trouble later. You can spray it with a water mist and remove with a putty knife. Dispose at the the recycling ceter hazard day or the like. Wrap in a large bag when you get it out. With new caps it will serve no purpose and freaks many out.

I have removed a few of these as RCA seemed to use that stuff a lot. Try to get it in one piece.

My humble opinion.

Best of luck.

Paul

Tubetalk1

Website Find

« Next Oldest | Next Newest »

Messages In This Thread

Zenith 6-D-2615 project - by klondike98 - 01-02-2016, 06:23 PM

RE: Zenith 6-D-2615 project - by titan1a - 01-02-2016, 09:57 PM

RE: Zenith 6-D-2615 project - by Paul Philco322 - 01-02-2016, 10:33 PM

RE: Zenith 6-D-2615 project - by klondike98 - 01-02-2016, 10:54 PM

RE: Zenith 6-D-2615 project - by klondike98 - 01-08-2016, 12:12 PM

RE: Zenith 6-D-2615 project - by Arran - 01-09-2016, 04:18 AM

RE: Zenith 6-D-2615 project - by OldRestorer - 01-09-2016, 08:22 AM

RE: Zenith 6-D-2615 project - by klondike98 - 01-09-2016, 09:52 AM

RE: Zenith 6-D-2615 project - by OldRestorer - 01-09-2016, 10:29 AM

RE: Zenith 6-D-2615 project - by codefox1 - 01-09-2016, 03:40 PM

RE: Zenith 6-D-2615 project - by klondike98 - 01-09-2016, 04:16 PM

RE: Zenith 6-D-2615 project - by klondike98 - 01-09-2016, 06:24 PM

RE: Zenith 6-D-2615 project - by Arran - 01-10-2016, 04:00 AM

RE: Zenith 6-D-2615 project - by klondike98 - 01-10-2016, 12:04 PM

RE: Zenith 6-D-2615 project - by klondike98 - 01-12-2016, 03:08 PM

RE: Zenith 6-D-2615 project - by klondike98 - 01-27-2016, 02:58 PM

RE: Zenith 6-D-2615 project - by OldRestorer - 01-27-2016, 04:44 PM

RE: Zenith 6-D-2615 project - by klondike98 - 01-27-2016, 05:08 PM

RE: Zenith 6-D-2615 project - by klondike98 - 07-23-2016, 09:38 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me