38-116 needs Dr. Philco.Resolved.

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

38-116 needs Dr. Philco.Resolved.

murf
Senior Member

Posts: 668
Threads: 144
Joined: Jun 2011
City: Elko,MN.

01-17-2016, 08:37 PM

Ok, makes sense I guess, if that is what it is supposed to read.
Just going by the values given on the schematics.
Noticed one of the 6L6 tubes had a weird vertical glow going on, where as the other did not.
Tested it in my hikock tester and it showed shorts on about 3 settings.

murf

(This post was last modified: 01-19-2016, 04:53 PM by murf.)

Find

« Next Oldest | Next Newest »

Messages In This Thread

38-116 needs Dr. Philco.Resolved. - by murf - 01-17-2016, 06:05 PM

RE: 38-116 needs Dr. Philco - by morzh - 01-17-2016, 07:08 PM

RE: 38-116 needs Dr. Philco - by murf - 01-17-2016, 08:37 PM

RE: 38-116 needs Dr. Philco - by morzh - 01-17-2016, 08:53 PM

RE: 38-116 needs Dr. Philco - by murf - 01-17-2016, 10:15 PM

RE: 38-116 needs Dr. Philco - by morzh - 01-17-2016, 10:57 PM

RE: 38-116 needs Dr. Philco - by murf - 01-19-2016, 05:02 PM

RE: 38-116 needs Dr. Philco - by morzh - 01-19-2016, 11:11 PM

RE: 38-116 needs Dr. Philco - by murf - 01-20-2016, 05:15 PM

RE: 38-116 needs Dr. Philco - by AI2V - 01-21-2016, 03:18 PM

RE: 38-116 needs Dr. Philco - by murf - 01-23-2016, 01:00 PM

RE: 38-116 needs Dr. Philco - by murf - 01-31-2016, 11:05 AM

RE: 38-116 needs Dr. Philco - by morzh - 01-31-2016, 11:57 AM

View a Printable Version

Users browsing this thread: 3 Guest(s)

Recent Posts
Philco Model 80 Transformer resistance
Just forget this number, it is useless anyway. Simply proceed with your project.morzh — 10:08 PM
Philco Model 80 Transformer resistance
My $0.02 is that it is a misprint. I tried to look up the value for the similar 84 and 37-84, and ther is no resistance...MrFixr55 — 09:51 PM
Philco Model 80 Transformer resistance
Thanks for the quick reply! Hmm...well that's good, so what am I seeing that's 1042 ohms on the schematic for the pow...Mike L — 08:46 PM
Philco Model 80 Transformer resistance
The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM
Philco Model 80 Transformer resistance
I have a feeling the primary winding on the power transformer is bad. My resistance reading on the primary side is 9 ohm...Mike L — 07:48 PM
Rusty Tuning Condenser
I would try Naval Jelly and use a soaked pipe cleaner to get it where it needs to go.RossH — 06:56 PM
38-10T chassis Restoration begins
Hello Dconant , they sold mica to use as a insulator between transistors and their heatsinks too. Rob I will remove th...radiorich — 02:52 PM
38-10T chassis Restoration begins
Thanks for the info guys. I always wondered why the use of mica. Now I know.dconant — 01:52 PM
38-10T chassis Restoration begins
Most common plastics have a dielectric constant in the 3-4 range whereas mica is around 6. This means that even if you w...Steve D — 01:46 PM
38-10T chassis Restoration begins
It is acceptable but not desirable. Plastic is not an approved cap dielectric, and even though a reasonably thick piece...morzh — 11:52 AM

Who's Online

There are currently 3739 online users. [Complete List]
» 2 Member(s) | 3737 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me