Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Fairbanks Morse Model 8a Problem
#5

I should say that I have voltage to the rf coil only on the shortwave bands when the 6k7 has the voltage also. Even then plate  voltage is 300v and pin 4 is 150. On Broadcast band that particular 6k7 (rf?) only has heater voltage 6.3 ac  the other 6k7 (if)has voltage all the time 300v plate 150 at pin 4..Sorry if did not make that clear.  

With the radio on shortwave and all tubes showing plate voltage....voltage is still 300v plate 6k7's and at the 5y3, bias is -55v at the filter, -60v at the 5y3. 

Thanks,
Bob


Messages In This Thread
Fairbanks Morse Model 8a Problem - by bm071 - 01-15-2016, 10:23 AM
RE: Fairbanks Morse Model 8a Problem - by bm071 - 01-18-2016, 10:24 AM
RE: Fairbanks Morse Model 8a Problem - by bm071 - 01-18-2016, 10:40 AM
RE: Fairbanks Morse Model 8a Problem - by bm071 - 01-18-2016, 08:37 PM
RE: Fairbanks Morse Model 8a Problem - by bm071 - 01-20-2016, 10:19 AM
RE: Fairbanks Morse Model 8a Problem - by bm071 - 01-20-2016, 06:55 PM
RE: Fairbanks Morse Model 8a Problem - by bm071 - 01-20-2016, 06:59 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
unknown radio
Hello Everyone How have you been doing for so long ? Please, does anyone know this radio ? It looks like the...claude.france — 05:17 AM
Want to get my Philco working again
Hi Perry and welcome, A few notes on the 41-295/300. Probably going to need to replace some of the failing rubber coa...Radioroslyn — 11:23 PM
Want to get my Philco working again
Just one question, Perry. You do know that the NFC North is confirmed LION(s) Territory!?!?GarySP — 09:44 PM
Want to get my Philco working again
There are actually quite the host of parts websites available! There’s Mouser, Digikey, etc. for general electronics com...jrblasde — 09:44 PM
Want to get my Philco working again
Thank you all for the replies. I’ve gotten into old stereos too so soldering isn’t too hard. Good to hear I can get the ...Gbtr6 — 08:23 PM
Want to get my Philco working again
I have one of those that I restored. Not a bad sounding/performing radio. Needs new socket and all new capacitors.rfeenstra — 06:22 PM
Want to get my Philco working again
Welcome to the Phorum, Perry. Your console is a 41-295X. You can access the schematic in our Philco Service found at t...GarySP — 06:21 PM
Want to get my Philco working again
Welcome to the Phorum. The reason the tube broke is probably because of those two gold helmets on top :PRodB — 05:37 PM
Want to get my Philco working again
See, the model, then go to, go to Philco, put the model in, open the document, locate the tube, locate it in the sch. Th...morzh — 03:23 PM
Want to get my Philco working again
Hi all, I have an old Philco radio that i remember fondly from my younger days. It sat out on the porch of my dad's a...Gbtr6 — 03:14 PM

[-]
Who's Online
There are currently no members online.

>