Precision E-200 sig gen

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Precision E-200 sig gen

leftwing25
Member

Posts: 85
Threads: 13
Joined: Jul 2015
City: Rockville, MD

02-03-2016, 08:11 PM

Nah, just like restoring old stuff. It all has a purpose if it works right. This thing actually has pretty accurate signal at the middle of the dial. Drifts off at either end. And I just don't trust old caps. Like to get other peoples experiences with these things too. Thanks for the reply, much appreciated. Ed

Find

« Next Oldest | Next Newest »

Messages In This Thread

Precision E-200 sig gen - by leftwing25 - 02-03-2016, 02:23 PM

RE: Precision E-200 sig gen - by klondike98 - 02-03-2016, 07:21 PM

RE: Precision E-200 sig gen - by leftwing25 - 02-03-2016, 08:11 PM

RE: Precision E-200 sig gen - by TV MAN - 02-04-2016, 11:03 AM

RE: Precision E-200 sig gen - by leftwing25 - 02-04-2016, 04:03 PM

RE: Precision E-200 sig gen - by Eliot Ness - 02-04-2016, 08:30 PM

RE: Precision E-200 sig gen - by leftwing25 - 02-05-2016, 01:12 PM

RE: Precision E-200 sig gen - by eeprof - 02-22-2016, 11:17 PM

RE: Precision E-200 sig gen - by klondike98 - 02-23-2016, 12:31 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM
Model 28L
Hello, I'm restoring a Philco 28L and the output transformer is open. Part number of the transformer is 32-7020. Can...HORSTE — 10:32 AM

Who's Online

There are currently 6309 online users. [Complete List]
» 2 Member(s) | 6307 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me