Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Precision E-200 sig gen
#4

I would recap it. They don't make those anymore. So, even if you re-sell it on Ebay, you are saving a piece of history at a minimum. I have recapped a couple of signal generators myself with pretty good success. Not too hard. They do the job. They are fairly close, but to be dead on, I use a frequency counter. It wont take you long to learn the settings once you have done this a few times. You can even align the dial or mark it with a piece of tape if it isn't linear. I find my Eico is closer than my Knight, plus it as a smoother waveform output. 

If I could find the place called "Somewhere", I could find "Anything" Icon_confused

Tim

Jesus cried out and said, "Whoever believes in me , believes not in me but in him who sent me" John 12:44


Messages In This Thread
Precision E-200 sig gen - by leftwing25 - 02-03-2016, 02:23 PM
RE: Precision E-200 sig gen - by klondike98 - 02-03-2016, 07:21 PM
RE: Precision E-200 sig gen - by leftwing25 - 02-03-2016, 08:11 PM
RE: Precision E-200 sig gen - by TV MAN - 02-04-2016, 11:03 AM
RE: Precision E-200 sig gen - by leftwing25 - 02-04-2016, 04:03 PM
RE: Precision E-200 sig gen - by Eliot Ness - 02-04-2016, 08:30 PM
RE: Precision E-200 sig gen - by leftwing25 - 02-05-2016, 01:12 PM
RE: Precision E-200 sig gen - by eeprof - 02-22-2016, 11:17 PM
RE: Precision E-200 sig gen - by klondike98 - 02-23-2016, 12:31 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 16B Parts
I think the chassis is painted.morzh — 08:13 PM
Philco 38-2 Automatic Tuning
Honestrly, the original is quite acceptable and, it seems to me, can be cleaned.morzh — 08:11 PM
Philco 41-608 changer coupler
Mondial left a thread about remanufacturing thois type coupler.morzh — 08:09 PM
IF can wire size and Rubber mounts?
Are you talking about rewinding or rewiring? For rewiring, meaning runnin wires to the coil from other components, the ...morzh — 08:08 PM
12' Philco
I wonder who would be able to "no stoop" with this one.morzh — 08:05 PM
IF can wire size and Rubber mounts?
Hello PHORUM members, I am still working on restoration of my PHILCO 37-640.  I want to start with rewiring the IF ca...georgetownjohn — 06:32 PM
Philco 41-608 changer coupler
I am working on a Philco 41-608 with the gear-driven changer.  The coupling (#35-2220) between the motor assembly and th...alangard — 06:29 PM
Gilfillan Brothers Car Radio?
There is a Mission Bell model 19/19A that could be what you’re looking for, Riders vol 4. It has the tube line-up of: 0Z...Joe Rossi — 05:01 PM
Looking for verification of correct schematic.
Definitely 870044RossH — 01:12 PM
12' Philco
Wonder if the chassis was big too.daveone23 — 12:38 PM

[-]
Who's Online
There are currently 3841 online users. [Complete List]
» 3 Member(s) | 3838 Guest(s)
AvatarAvatarAvatar

>