My new RCA 6T-7 tombstone

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

My new RCA 6T-7 tombstone

Dan Walker
Senior Member

Posts: 370
Threads: 102
Joined: Jul 2011
City: Calgary, AB, CA

#16

02-08-2016, 01:06 PM

Warm to me is when I can do some work in the garage and not have cold hands. I guess about 60 F would be good.
It is supposed to get to get to 50F this week, but I have all my stripping stuff in the house.
I have all my Mohawk products, lacquer, stripper, shellac and touch up stuff in the basement and I don't want to take it out until it does not freeze at night.. It still freezes every night.
Ideally I like to do this sort of stuff when it is about 75F.

Living in Calgary Alberta

Find

« Next Oldest | Next Newest »

Messages In This Thread

My new RCA 6T-7 tombstone - by Dan Walker - 02-05-2016, 10:50 AM

RE: My new RCA 6T-7 tombstone - by KCMike - 02-05-2016, 11:10 AM

RE: My new RCA 6T-7 tombstone - by morzh - 02-05-2016, 11:11 AM

RE: My new RCA 6T-7 tombstone - by Eliot Ness - 02-05-2016, 12:45 PM

RE: My new RCA 6T-7 tombstone - by Paul Philco322 - 02-05-2016, 04:27 PM

RE: My new RCA 6T-7 tombstone - by Dan Walker - 02-05-2016, 07:56 PM

RE: My new RCA 6T-7 tombstone - by Fred Taylor - 02-05-2016, 10:30 PM

RE: My new RCA 6T-7 tombstone - by Arran - 02-06-2016, 01:55 AM

RE: My new RCA 6T-7 tombstone - by Dan Walker - 02-06-2016, 11:06 AM

RE: My new RCA 6T-7 tombstone - by KCMike - 02-06-2016, 11:52 AM

RE: My new RCA 6T-7 tombstone - by Dan Walker - 02-07-2016, 12:30 AM

RE: My new RCA 6T-7 tombstone - by palegreenthumb - 02-07-2016, 01:15 AM

RE: My new RCA 6T-7 tombstone - by Fred Taylor - 02-07-2016, 08:17 AM

RE: My new RCA 6T-7 tombstone - by Dan Walker - 02-08-2016, 10:40 AM

RE: My new RCA 6T-7 tombstone - by sam - 02-08-2016, 12:38 PM

RE: My new RCA 6T-7 tombstone - by Dan Walker - 02-08-2016, 01:06 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM

Who's Online

There are currently 2742 online users. [Complete List]
» 4 Member(s) | 2738 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me