Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Model 20 recently acquired
#12

Thanks for the information, Arran.  I did not know the 80 tube was built in a GT casing.  I've always seen globe or ST only.  I agree with you after taking a closer look; those look to be original tube socket rivets.  Steve, if you don't have it you will want to locate a tube shield.  They pop up from time to time on Ebay, and I don't recall where I saw it but there is someone out there that makes reproductions.  A little patience and some sheet metal and you could probably fabricate a working version yourself.  Original-style speaker cloth will be a bit more of a challenge to locate.  Take care, Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan


Messages In This Thread
Model 20 recently acquired - by SteveinAlaska - 02-22-2016, 02:31 AM
RE: Model 20 recently acquired - by klondike98 - 02-22-2016, 08:21 AM
RE: Model 20 recently acquired - by GarySP - 02-22-2016, 08:36 AM
RE: Model 20 recently acquired - by Arran - 02-23-2016, 01:55 AM
RE: Model 20 recently acquired - by SteveinAlaska - 02-22-2016, 01:13 PM
RE: Model 20 recently acquired - by klondike98 - 02-22-2016, 01:29 PM
RE: Model 20 recently acquired - by morzh - 02-22-2016, 08:33 PM
RE: Model 20 recently acquired - by radiohenry - 02-22-2016, 08:50 PM
RE: Model 20 recently acquired - by Crist Rigotti - 02-22-2016, 08:51 PM
RE: Model 20 recently acquired - by morzh - 02-22-2016, 08:52 PM
RE: Model 20 recently acquired - by Arran - 02-23-2016, 02:04 AM
RE: Model 20 recently acquired - by GarySP - 02-23-2016, 09:01 AM
RE: Model 20 recently acquired - by gregb - 03-20-2016, 11:38 AM
RE: Model 20 recently acquired - by morzh - 03-20-2016, 11:51 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently no members online.

>