1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 39-25 -- No reception
Radioroslyn
Phorum Expert
*****
Posts: 7,288
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#14

03-05-2016, 07:50 PM
Well that's better but grid 2 needs to be at 150vdc. So try disconnecting #7 And see if the voltage goes up. If not check the 1/2 ohm section of the osc coil may be open. Measure the voltage on both side of winding should be the same on both sides around 150vdc.

Terry
(This post was last modified: 03-05-2016, 07:51 PM by Radioroslyn.)
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco 39-25 -- No reception - by KRMiskimon - 03-02-2016, 08:27 PM
RE: Philco 39-25 -- No reception - by Warren - 03-02-2016, 11:31 PM
RE: Philco 39-25 -- No reception - by KRMiskimon - 03-02-2016, 11:35 PM
RE: Philco 39-25 -- No reception - by morzh - 03-02-2016, 11:56 PM
RE: Philco 39-25 -- No reception - by KRMiskimon - 03-03-2016, 12:43 AM
RE: Philco 39-25 -- No reception - by KRMiskimon - 03-03-2016, 12:47 AM
RE: Philco 39-25 -- No reception - by Radioroslyn - 03-03-2016, 01:35 AM
RE: Philco 39-25 -- No reception - by TV MAN - 03-03-2016, 10:57 AM
RE: Philco 39-25 -- No reception - by Steve Davis - 03-03-2016, 11:40 AM
RE: Philco 39-25 -- No reception - by klondike98 - 03-03-2016, 12:43 PM
RE: Philco 39-25 -- No reception - by KRMiskimon - 03-03-2016, 09:40 PM
RE: Philco 39-25 -- No reception - by Radioroslyn - 03-03-2016, 11:42 PM
RE: Philco 39-25 -- No reception - by KRMiskimon - 03-05-2016, 06:55 PM
RE: Philco 39-25 -- No reception - by Radioroslyn - 03-05-2016, 07:50 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Rusty Tuning Condenser
Give the tuner a good wash in Dawn and hot water. Then set tuner in a plastic container and cover with vinegar let soak ...David — 12:53 PM
Rusty Tuning Condenser
If you have rust between the vanes, I wonder how you get the NJ in between, and how you then wipe it off.morzh — 12:02 PM
Philco 60 Squealing
If the noise is still there, the OPT might just be OK. Or so we hope.morzh — 12:01 PM
Philco 60 Squealing
You would probably be replacing the OPT.RodB — 10:54 AM
Philco 60 Squealing
I have been playing the radio for a while now and doing well. Turned it on today and all I got was a whole lot of noise....dconant — 09:39 AM
Rusty Tuning Condenser
Thanks guys. I think I'll give the Naval Jelly a try since I can better control where it goes.dconant — 09:23 AM
Philco Model 80 Transformer resistance
Just forget this number, it is useless anyway. Simply proceed with your project.morzh — 10:08 PM
Philco Model 80 Transformer resistance
My $0.02 is that it is a misprint. I tried to look up the value for the similar 84 and 37-84, and ther is no resistance...MrFixr55 — 09:51 PM
Philco Model 80 Transformer resistance
Thanks for the quick reply! Hmm...well that's good, so what am I seeing that's 1042 ohms on the schematic for the pow...Mike L — 08:46 PM
Philco Model 80 Transformer resistance
The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM

[-]
Who's Online
There are currently 2925 online users. [Complete List]
» 1 Member(s) | 2924 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration