Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Thunder crashing 1401
#11

Thanks for all of this great information, everyone. I will double check the caps and give the tube sockets and tube pins a good scouring. If that doesn't take care of the problem, then it's got to be the mica's. I've had radios with silver mica disease before, so I've heard the tell-tale signs of it. This one isn't as loud or overpowering as others I've experienced in the past, so perhaps it is one or more of the sockets causing the 'whooshing' & crackling noise after all. One thing is for sure, I've never had good luck with removing the mica wafers from those small IF cans. Icon_thumbdown 

Greg V.
West Bend, WI
Member WARCI.org


Messages In This Thread
Thunder crashing 1401 - by NostalgiaRadioTime - 03-02-2016, 11:57 PM
RE: Thunder crashing 1401 - by Radioroslyn - 03-03-2016, 01:53 AM
RE: Thunder crashing 1401 - by Arran - 03-03-2016, 05:28 AM
RE: Thunder crashing 1401 - by kiwi_steve - 03-03-2016, 11:04 PM
RE: Thunder crashing 1401 - by Arran - 03-04-2016, 05:00 AM
RE: Thunder crashing 1401 - by Paul Philco322 - 03-04-2016, 09:26 PM
RE: Thunder crashing 1401 - by codefox1 - 03-05-2016, 10:16 AM
RE: Thunder crashing 1401 - by OZ4 - 03-05-2016, 12:38 PM
RE: Thunder crashing 1401 - by radiohenry - 03-05-2016, 05:06 PM
RE: Thunder crashing 1401 - by Radioroslyn - 03-05-2016, 07:59 PM
RE: Thunder crashing 1401 - by NostalgiaRadioTime - 03-06-2016, 01:50 AM



Users browsing this thread: 6 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
You would probably be replacing the OPT.RodB — 10:54 AM
Philco 60 Squealing
I have been playing the radio for a while now and doing well. Turned it on today and all I got was a whole lot of noise....dconant — 09:39 AM
Rusty Tuning Condenser
Thanks guys. I think I'll give the Naval Jelly a try since I can better control where it goes.dconant — 09:23 AM
Philco Model 80 Transformer resistance
Just forget this number, it is useless anyway. Simply proceed with your project.morzh — 10:08 PM
Philco Model 80 Transformer resistance
My $0.02 is that it is a misprint. I tried to look up the value for the similar 84 and 37-84, and ther is no resistance...MrFixr55 — 09:51 PM
Philco Model 80 Transformer resistance
Thanks for the quick reply! Hmm...well that's good, so what am I seeing that's 1042 ohms on the schematic for the pow...Mike L — 08:46 PM
Philco Model 80 Transformer resistance
The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM
Philco Model 80 Transformer resistance
I have a feeling the primary winding on the power transformer is bad. My resistance reading on the primary side is 9 ohm...Mike L — 07:48 PM
Rusty Tuning Condenser
I would try Naval Jelly and use a soaked pipe cleaner to get it where it needs to go.RossH — 06:56 PM
38-10T chassis Restoration begins
Hello Dconant , they sold mica to use as a insulator between transistors and their heatsinks too. Rob I will remove th...radiorich — 02:52 PM

[-]
Who's Online
There are currently 2971 online users. [Complete List]
» 2 Member(s) | 2969 Guest(s)
AvatarAvatar

>